All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.3.1! Most orders shipping same day!  Departing from Florida, U.S.A.  

F4 processors

Grid List

Set Descending Direction

11-20 of 23

  1. Regular Price:

    $25.00
    View Details

    The Flip32 F4 Dual Gyro edition. It is two Flight controllers in one!  Two gyros one board. now they can only be used one at a time, but the future updates will never tell what will be next. With this Feature you can future proof yourself, and have another trick up your sleeve, by having options on the board. One super sensitive (SSG) High rate MPU-ICM20608 Gyro and one Proven rock-solid MPU-6000 that will run on in about any setup. With this combo you can have more flexibility. If you are not sure your new setup will be prime for the MPU-ICM20608, you can give it a try, if you can not get all the bad behaviors out you can change the Gyro in the GUI, and start flying, Improve the problems, and then swap back over when your ready.  If your new to the hobby the forgiving MPU-6000 will help you learning, and when your ready, you have room to grow to the ICM20608. If you are in a race, a couple gate crashes later, your craft gyro is feeling the pain and getting a little shaky, swap over to the MPU-6000 in seconds to finish the last heat! Give you many opportunities. It can change depending on if you can soft-mount, already ready for any installation.  

    Learn More
  2. Regular Price: $85.99

    Special Price $79.99

    View Details

    now shipping always the newest Asgard V5.1, has all the improvements . All V5.1 are Silicone conformal coating for the protection from the elements.   Better Current Protection. 5v Regulator Upgrade. Custom Hex pre installed. Silicone conformal coating Note for 2.3 users. XM+ on UART6. Use the OMNIBUSF4SD hex. Then  ASGARD users must explicitly change the pin mapping by executing the following CLI command. "resource inverter 6 c9" - then make sure to safe  F4, with Betaflight OSD, 150A PCB and 30-40A esc's all on a 12 layer board with 2oz copper. Mounting holes 30.5 x 30.5mm. Incl. OSD / SD Card / F4 FC / Current sensor / BEC. All Flight controllers are Silicone conformal coating for the protection.  

    All units flashed with stable BetaFlight 2.3.0. Take advantage of all the new features out of the box, Automatic Notch filter, turtle mode, Camera control, Increased motor output resolution, OSD improvements, and much , more

    Now Shipping V5.1! Asgard (F4 FC+ Bl-heli_S ESCs+OSD+SD+Current Sensor) The Flip32 OMNIBUS F4 AIO aka Asgard has 4 24amp BLheli_s speed controllers built-in!  We also packed a BetaFlight OSD, Powerful F4, Current Sensor , 5v 1.5a BEC. Just connect your camera and TX, then motors and Rx, and be ReadyToFly. With Free repair service, Build-in power distribution board with current sensor on board. 2-4 cell battery supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. 

     Repair/replacement service is available if needed to get you back in the air asap. If you burn one ESC or the OSD or any other part, 90% of the time we can fix it with NO EXTRA FEE! . in worst case we are offering $45 no questions asked replacements for our customers. This covers electrical damage and fried esc’s if that should ever occur.  we are very experienced with these repairs, and most of the time can repair the Asgard with NO EXTRA FEE

    Only place were the board includes two S.H cables with the board to make the connections, a capacitor is includes with the board . it is HIGHLY RECOMMENCED to use a capacitor with this board at the input . It's a Flight Controller, PDB and Esc's all rolled into one nice little package! If space is at a premium or you are just looking to do a super clean build, then this is what you are looking for. The Asgard boasts an F4 processor and 24amp 4-in-1 esc that is compatible with the latest D-shot protocol to get that super smooth controller and crispy response.One of the awesome features about having an AIO FC is that you can tune your PIDs directly through your Transmitter via the built in OSD! Finally, no more massive flight control stacks! Using the latest Asgard ESC's combined into a simple board with the latest hardware you will get the cleanest of builds!


    What does Blheli-S 16.67 do? Means no more external beeper! just set the beeper and your motors will beep to find your quad instead of you needing to add more external parts. 


    FIRMWARE for MX and MX+  for software SBUS Inverter for XOR gates, this will be rolled into BF 3.2.0. this firmware is shipping with all new orders sent 

     https://www.dropbox.com/s/hj4jd3av8oko9ji/betaflight_3.1.6_Asgard_PC9_HIGH_SBUSInverter_Enabled?dl=0


    • STM32 F405 MCU (Spi connected to Gyro)
    • Better Current Protection w/  5v Regulator Upgrade
    • BetaFlight 3.2 with BlheliS 16.67 RC-Commands 
    • Silicone conformal coating 
    • Custom Hex pre installed; Wires and Capacitor included
    • 4 - 24A Bl_heli_s Speed controllers 
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Built in PBD
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm  w/ M3 holes\
    • comes with cables & capacitor needed for higher currents 
    • Target: Ominibus F4 SD

    This Flight controller with a powerful F4 AIO.  aka Asgard / Omnibus F4 AIO (24amp 4-in-1 ESC with Dshot + Flight Controller)

    FIRMWARE for MX and MX+  for software SBUSInverter, this will be rolled into BF 3.2.0 Inverted on Uart6

     https://www.dropbox.com/s/hj4jd3av8oko9ji/betaflight_3.1.6_Asgard_PC9_HIGH_SBUSInverter_Enabled?dl=0


    1x FC+ESC + 2 S.H connection cables



    To install with the Power BACK and FETS UP. type in the CLI

    resource MOTOR 1 B00

    resource MOTOR 2 A03

    resource MOTOR 3 B01

    resource MOTOR 4 A02

    save

    in the GUI - 

    Pitch = 180

    Yaw= 90


    24a esc, AIO, aio flight controller, airbot asgard, Airbot Asgard / Omnibus F4 AIO, Asgard, Dshot, dshot 600, omnibus aio, omnibus asgard aio, omnibus f4 aio, F4 aio, omnibus aio. Flip32 F4 Omnibus AIO


    If you would like to configure the board in a different orientation, you can learn more about Motor Remapping in BetaFlight here.  https://github.com/betaflight/betaflight/wiki/Remapping-Motors-with-Resource-Command-(3.1)

    Learn More
  3. Regular Price: $32.99

    Special Price $29.99

    View Details

    The OMNIBUS F4 V3 , with a barometer, sports a super clean SBEC power supply when powered with direct lipo. The Flight controller will say cool, and is perfect for "Pod" style designs. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: S-bus is built in default selected. If you want to use PPM. you need to CUT the track, then bridge the PPM pad, even the Sbus pads do not look "bridged" with solder.but they are connected inside the board, no bridging is needed for a super clean look.  OMNIBUS F4 V3 header through-hole is connected to UART6, not UART1 like all others. DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • SmartAudio 
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)


    Setup SoftSer 11 for runcam control:

    resource Motor 5 none

    resource Motor 6 none

    resource serial_rx 11 A1

    resource serial_tx 11 A8


    Get Mag working on UART3/I²C2:

    resource Serial_TX 3 none

    resource Serial_RX 3 none

    resource i2c_scl 2 b10

    resource i2c_sda 2 b11

    Learn More
  4. Regular Price:

    $19.99
    View Details
  5. Regular Price: $23.99

    Special Price $19.99

  6. Regular Price:

    $18.99
    View Details
  7. Regular Price:

    $32.99
    View Details

    The OMNIBUS F4 V2.5 , with or without the LDO installed on the board when powered with direct lipo. pick what you need according to your  build style designs. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F4 V2.5 header through-hole is connected to UART1,DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • SmartAudio 
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)

    Learn More
  8. Regular Price: $37.99

    Special Price $34.99

    View Details

    All Flight Controllers are  flashed and tested with the newest stable BetaFlight 3.2.1. Take advantage of all the new features, Automatic Notch filter, turtle mode, Camera control,DShot1200, Increased motor output resolution, OSD improvements, and much , more

    Now Shipping the Newest 5V! with easier PPM/S_sub selector , and improved internal layout  and more robust build in BEC to solve any problems with some camera/Tx combos. Only place to get the freshest & NEWEST Genuine OMNIBUS total Flight Controller line that each  portion of the sales goes to back to the BF project. The only place with correct updated documentation included  with the board, reinforced USB plug and Pin headers in the bag if needed, always tested and flashed the the newest firmware ! BEWARE of other shops claiming V3 when it is not, ,make sure your is a true V3 here. Others shops are buying clones  and selling as originals and do not understand.

    BEWARE OF THE CLONE-because of the popularly the direct copys have come. They are all cloning the Older V2 with a massive Current Club24A problem. We also give a portion of sales back to the community to keep improving the software.

         Now with SD card reader and Baro The Omnibus F4 Pro has the F4 processor has a Built-in Current / Voltage Sensor . Built-in OSD, video filtering, Baro, and LDO. Supports D-Shot out of the box with no Modification. Tuning could not be easier with the help of the black box SD card reader and tuning via transmitter in the OSD. It is now possible to connect your Smartaudio capable VTX . The Flip32 Omnibus flight controller uses the MPU6000 over SPI for the best possible flight performance. Along with the MPU6000 are a and an AB7456 OSD chip (an upgraded MAX7456) for the BetaFlight integrated OSD. You won't need a PDB with this build because there is a high performance 5v, 1.5a STMicrocontroller L78 voltage regulator, so you can plug the flight battery right into the flight controller.The  Flip32 Omnibus flight controller the first  F4 flight controller with a MAX7456 OSD chip directly connected to the flight controller, so it can be configured from the BetaFlight configurator.  The Omnibus F4 features the STM32F405 F4 processor, built-in BetaFlight OSD, video filtering, microsd blackbox, and BMP280 Barometer. MPU6000 Low noise Gyro, in most cases soft mounted is not necessary, and is more accurate when attached to the frame. If you do see any symptoms, we high recommend to soft mount the motors first. 

    The SmartAudio support has been included in BF3.1.0! (SmartAudio V2 VTX Control)-it is now possible to connect your Smartaudio capable VTX.  OMNIBUS F4 SD (aka OMNIBUS F4 V2) 2016-12-08 - Connect RSSI wire to RSSI input on J4. [BF] Working IR Transponder. This feature was included in the BF3.1.0 . [BF] Fully configurable software serial"

    INSTALL THE BETAFLIGHT CONFIGURATOR

    NEW OSD tab in Betaflight configurator lets you setup and configure OSD settings on the fly!

    Flip32 Omnibus was designed a 36mmx36mm (30.5mm mount holes) community version of his AIO boards. It’s called Flip32 OMNIBUS and it’s outstanding. The great thing is that the board is based on what the community really wanted and it allows a very clean build by providing pin holes for almost every connection. You can power it directly from your battery by using BAT/GND pins. The following list some of the components included:

    • STM32 F403 MCU (Spi connected to Gyro)
    • Buildin Current/Voltage sensor!
    • Firmware hex = OMNIBUSF4SD hex from dropdown. 
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • Smartaudio capable VTX PID Programming 
    • D- Shot Supported (no Modification) 
    • OSD (configured over Betaflight UI)
    • SD CARD READER + And BARO ADDED in V2
    • SBUS/PPM + DSMX Ports
    • SmartAudio V2 via J10
    • current + voltage + rssi + buzzer as pins
    • 4x 3 pin holes for ESCs + 4x signal pin holes
    • IR pins for lap timing transponder

    All Flight controllers are flashed and tested with Betaflight 3.2.1. Make sure to add the Silicone Modified Conformal Coating addition apply after testing and soldering. Protects electronics from moisture, corrosion, thermal shock, and static discharges.

    Learn More
  9. Regular Price: $24.99

    Special Price $19.99

  10. Regular Price:

    $30.99
    View Details

    The OMNIBUS F4 , Rev 2 now has the option to have the regulator off the board if one plans to power with 5 volts. Also rev 2 has other internal RaM power improvements . Or the LDO can be installed on the board. with LDO to be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming the newest or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F4 V2.5 header through-hole is connected to UART1,DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)

    Learn More

Grid List

Set Descending Direction

11-20 of 23