All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.5.1 (september 8th)! Departing from Florida, U.S.A.  

F4 processors

Grid List

Set Descending Direction

9 Item(s)

  1. Regular Price: $29.99

    Special Price $27.99

    View Details
  2. Regular Price: $26.00

    Special Price $24.50

    View Details
  3. Regular Price: $29.99

    Special Price $25.99

    View Details

    The Flip32 OMNIBUS F4 NANO LC is a good option if you do not need a Data flash Logger on board, and you power the camera via the FC. If not the cheaper Nano V2 will be the same results. If you need a Data flash the V2 is the same layout with a Memory chip. This flight controller takes away the black box, but add a small filter to the power line on the Camera connecor now in 20x20mm mounting hole size (3m holes).Target "OMNIBUS F4" to update the firmware. With F4 and Betaflight OSD. 2-4 cell battery supported. 4s is currently supported with WITH onboard BEC , just connect to the FC and it will power., but you can still have the current and Voltage readings on the OSD, and is supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Target "OMNIBUS F4" to update the firmware
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S). 4s supported
    • 20x20mm  w/ M3 holes

    This Flip32 Omnibus F4 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board is a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, Smart Audio Support, Camera Control, ESC32 telemetry, and more. Powerful F4 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, 3.3 Volt power for spectrum users. The special feature of this Fc is a super Clean Power L/C filter to power the camera. This cuts out any extra noise in the picture for super clear video feed.

    (SBUS + SmartPort + SmartAudio + CamControl) Config:

    Code:
    # Betaflight / OMNIBUSF4SD (OBSD) 3.2.2 Nov 11 2017 / 00:39:14 (77782e602) MSP API: 1.36
    
    resource SERIAL_TX 11 A10
    
    feature SOFTSERIAL
    feature TELEMETRY
    feature LED_STRIP
    
    serial 0 32 115200 57600 0 115200
    serial 5 64 115200 57600 0 115200
    serial 30 2048 115200 57600 0 115200
    
    set serialrx_provider = SBUS

    ESC32 telemetry mod CONFIG: 

    Here is a config for the mod. Don't forget to select one of DSHOT for ESC/Motor protocol.

    Code:
    resource ADC_CURR 1 NONE
    feature ESC_SENSOR
    serial 2 1024 115200 57600 0 115200
    set current_meter = ESC
    set battery_meter = ESC


    Camera Control MOD: working with our Add on board here; try 
    inverted = off and on

    resource CAMERA_CONTROL C06
    set camera_control_ref_voltage = 295
    set camera_control_internal_resistance = 400
    set camera_control_inverted = off


    Learn More
  4. Regular Price: $27.99

    Special Price $24.99

    View Details

    Installed with BetaFlight 3.3.2. This firmware will enable all the features , Baro + Blackbox+ LED Strip.  The Flip32 OMNIBUS F4 NANO now in 20x20mm mounting hole size (3m holes). Blackbox chip installed. The only place with a Data flash chip option installed on the board, and a free cable.  With F4 and Betaflight OSD. 2-4 cell battery supported. 4s is currently supported with onboard BEC , just connect to the FC and it will power., but you can still have the current and Voltage readings on the OSD, and is supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Target "OMNIBUS F4SD" to update the firmware
    • SBUS/PPM + DSMX Ports
    • Blackbox data flash chip
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S). 4s supported
    • 20x20mm  w/ M3 holes

    This Flip32 Omnibus F4 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board is a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, Smart Audio Support, Camera Control, ESC32 telemetry, and more. Powerful F4 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, 3.3 Volt power for spectrum users. The special feature of this Fc is it has a Black Box logging chip on board. This will allow you to log some flying and check them out on the black box viewer to see your motor graph and adjust your filters for a super crisp tune, or trouble shoot a problem.

    (SBUS + SmartPort + SmartAudio + CamControl) Config:

    Code:
    # Betaflight / OMNIBUSF4SD (OBSD) 3.2.2 Nov 11 2017 / 00:39:14 (77782e602) MSP API: 1.36
    
    resource SERIAL_TX 11 A10
    
    feature SOFTSERIAL
    feature TELEMETRY
    feature LED_STRIP
    
    serial 0 32 115200 57600 0 115200
    serial 5 64 115200 57600 0 115200
    serial 30 2048 115200 57600 0 115200
    
    set serialrx_provider = SBUS

    ESC32 telemetry mod CONFIG: 

    Here is a config for the mod. Don't forget to select one of DSHOT for ESC/Motor protocol.

    Code:
    resource ADC_CURR 1 NONE
    feature ESC_SENSOR
    serial 2 1024 115200 57600 0 115200
    set current_meter = ESC
    set battery_meter = ESC


    Camera Control MOD: working with our Add on board here; try 
    inverted = off and on

    resource CAMERA_CONTROL C06
    set camera_control_ref_voltage = 295
    set camera_control_internal_resistance = 400
    set camera_control_inverted = off
    Learn More
  5. $25.00
    View Details

    The Flip32 F4 Dual Gyro edition. It is two Flight controllers in one!  Two gyros one board. now they can only be used one at a time, but the future updates will never tell what will be next. With this Feature you can future proof yourself, and have another trick up your sleeve, by having options on the board. One super sensitive (SSG) High rate MPU-ICM20608 Gyro and one Proven rock-solid MPU-6000 that will run on in about any setup. With this combo you can have more flexibility. If you are not sure your new setup will be prime for the MPU-ICM20608, you can give it a try, if you can not get all the bad behaviors out you can change the Gyro in the GUI, and start flying, Improve the problems, and then swap back over when your ready.  If your new to the hobby the forgiving MPU-6000 will help you learning, and when your ready, you have room to grow to the ICM20608. If you are in a race, a couple gate crashes later, your craft gyro is feeling the pain and getting a little shaky, swap over to the MPU-6000 in seconds to finish the last heat! Give you many opportunities. It can change depending on if you can soft-mount, already ready for any installation.  

    Learn More
  6. Regular Price: $32.99

    Special Price $27.99

    View Details

    The OMNIBUS F4 V5 , with a barometer, and 6s support.  sports a super clean SBEC power supply when powered with direct lipo. The Flight controller will say cool, and is perfect for "Pod" style designs. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: S-bus is built in default selected. If you want to use PPM. you need to CUT the track, then bridge the PPM pad, even the Sbus pads do not look "bridged" with solder.but they are connected inside the board, no bridging is needed for a super clean look.  OMNIBUS F4 V3 header through-hole is connected to UART6, not UART1 like all others. DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • SmartAudio 
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)


    Setup SoftSer 11 for runcam control:

    resource Motor 5 none

    resource Motor 6 none

    resource serial_rx 11 A1

    resource serial_tx 11 A8


    Get Mag working on UART3/I²C2:

    resource Serial_TX 3 none

    resource Serial_RX 3 none

    resource i2c_scl 2 b10

    resource i2c_sda 2 b11


    OMNIBUS F4 V5.1 Flight Control

    Learn More
  7. $32.99
    View Details

    The OMNIBUS F4 V2.5 , with or without the LDO installed on the board when powered with direct lipo. pick what you need according to your  build style designs. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F4 V2.5 header through-hole is connected to UART1,DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • SmartAudio 
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)

    Learn More
  8. $30.99
    View Details

    The OMNIBUS F4 , Rev 2 now has the option to have the regulator off the board if one plans to power with 5 volts. Also rev 2 has other internal RaM power improvements . Or the LDO can be installed on the board. with LDO to be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming the newest or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F4 V2.5 header through-hole is connected to UART1,DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)

    Learn More

Grid List

Set Descending Direction

9 Item(s)