All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.4.0(July 8th)! Departing from Florida, U.S.A.  

F3 processors

Grid List

Set Descending Direction

5 Item(s)

  1. Regular Price: $28.00

    Special Price $25.00

    F3 MCU, incl. F3 FC ACRO and MinimOSD. UART, Blackbox

    STM32 F303 MCU,

    Runs Cleanflight firmware • SPRacing HEX

    8PWM input (Pinheaders) •

    8PWM output (Pinheaders) •

    Mounting holes 30.5x30.5mm •

    128Mb Flash(16M Byte)

    Learn More
  2. Regular Price:

    $30.00
    View Details

    The OMNIBUS F3 PRO V3, beware of faulty v2 clones , Build in "PBD" Style current sensor and will be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F3  header through-hole is connected to UART3,DSMX receiver is UART port
    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support (Dshot600 to 1200)
    • SBUS/PPM + DSMX Ports
    • 5v3a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes
    • Low price

    This Flight controller is a  powerful F3 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. All pack with a low price, with a current sensor.


    A. OMNIBUS F3 Pro -  - Single Wire Software Serial

    PinLabelS.AudioTrampS.PortNote
    A8LED stripNGNGNG
    B4PPM (*1)OK?OKWhen PPM not in use
    B6PWM8/SCLOKOKOKI2C must be de-configured? Need furthe testing.
    B7PWM7/SDAOK??Ditto

    B. B07 (PWM7/SDA) works with S.Audio on 3.2, no extra config needed (I2C resources aren't mapped per default).

    C. Camera Control OSD with work on ANY PWM5-PWM6 using the Camera Control add on board here

    D. Extra Timer: If you are using S.BUS or other Serial RX receivers, then you can move your receiver input from SBUS/PPM header (J8) to UART3 RX (F3: J22/PWM6, F3 Pro: J12/PWM6), and make the SBUS/PPM header dedicated for PPM signal. The PPM signal is connected to MCU pin PB4, and you can use this for single-wire software serial. (see picture) This also means that when PPM is in use, UART3 cannot be used. However, if you are out of serial ports, using PPM and need one more, you can remove the SBUS resistor as described below and uncomment this line from the BetaFlight source code #define AVOID_UART3_FOR_PWM_PPM. This will enable both PPM and UART3


    1. Remove the SBUS jumper, leave PPM jumper intact.
    2. Connect SBUS signal to PWM6.
    3. Connect SmartPort signal to SBUS/PPM.
    4. Enter the CLI commands below (they will setup SBUS on UART3 also).

    Code:
    resource SERIAL_TX 11 B04
    feature -RX_PPM
    feature RX_SERIAL
    feature SOFTSERIAL
    feature TELEMETRY
    serial 2 64 115200 57600 0 115200
    serial 30 32 115200 57600 0 115200
    set serialrx_provider = SBUS

    E.


    Learn More
  3. Regular Price:

    $54.99
    View Details
  4. Regular Price: $27.99

    Special Price $25.99

    View Details

    All units are tested and flashed with stable BetaFlight 2.3.4 . Supports 4s Battery input.  Take advantage of all the new features, Automatic Notch filter, turtle mode, Camera control,SmartAudio, Increased motor output resolution, OSD improvements, and much , more

    The Flip32 OMNIBUS F3 NANO in 20x20mm mounting hole size (3m holes). Target "OMNIBUS" to update the firmware. Build-in power distribution board PDB with current sensor on board. 2-4s cell battery , current and Voltage readings on the OSD. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.

    UART3 is used for DSM Sat AND SBUS

    Features:

    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Target "OMNIBUS" to update the firmware
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Built in PBD ( 60 AMPS sensing) 
    • Barometer
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4s)
    • 20x20mm  w/ M3 holes
    • Note: This is the newest V3. the board color can be Black or Blue.

    This  Flip32 Omnibus F3 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, and smart Audio Support. Powerful F3 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, the on-board BEC will work for 2s-4s will support the Current sensors and voltage readings still supported over OSD, but will not have a BEC power on 4s.  This FC  will also be capable of replacement for PDB allowing you for super tight build connecting the ESC to the FC.

    Learn More
  5. Regular Price: $39.99

    Special Price $35.00

    View Details
    TUNE YOUR PIDs VIA OSD!

    Per-load with BETAFLIGHT 3.0.1  and  scarab osd 1.6.4.0! Do not bang your head on the desk trying to figure out all the firmware configuration settings. We have spent  a lot of time, so this FC & OSD is the most Ready to Fly It can be, ONLY FROM RTFQuads, we have built and know these Flight Controllers  more then anyone else, just load up the GUI and move the OSD objects around to your liking ! Less time on the bench more time in the Air! 

    get the OSD GUI HERE: https://github.com/ShikOfTheRa/scarab-osd/archive/v1.6.4.0.zip

    Make a super Clean build with less parts counts and super clean look with the 4in1 ESC. Upgraded AIO FC, based on F302 MCU, incl. F3 FC / OSD/ USB / Blackbox / Current Sensor / BEC / Compass / Baro in 35x35mm Board. Compare to F1 MCU, it supports more UART, runs faster and has Blackbox. The Connection between FC-OSD-USB will be managed automaticlly, NO DIP SWITCH needed

    • STM32 F303 MCU, Runs Cleanflight firmware 
    • no Barometer &Compasss 
    • MPU6050 
    • 8PWM output as PLUG,4x PWM output as Solder pads
    • 35x35mm, mount holes 30x30mm 
    • 128Mb Flash(16M Byte) 
    • 5v 2A BEC (up to 4s) 
    • Current and voltage sensor incl. 
    • Smart button instead of DIP switch

    Smart connection When powered by LIPO(no USB cable attached) When USB cable plug in, the USB will connect to FC automaticlly, you can change the connect to "USBOSD" by press Smart Button for 1S then release when USB cable pluged in.(Then LED shows OFF) Smart Button 's LED is ON Smart Button 's LED is ON Smart Button 's LED is OFF FC USB USB OSD FC OSD press Smart Button for 1S then release press Smart Button for 1S th

    Learn More

Grid List

Set Descending Direction

5 Item(s)