All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.3.1! Most orders shipping same day!  Departing from Florida, U.S.A.  

Flip Series

Grid List

Set Descending Direction

21-30 of 51

  1. Regular Price: $37.99

    Special Price $34.99

    View Details

    All Flight Controllers are  flashed and tested with the newest stable BetaFlight 3.2.1. Take advantage of all the new features, Automatic Notch filter, turtle mode, Camera control,DShot1200, Increased motor output resolution, OSD improvements, and much , more

    Now Shipping the Newest 5V! with easier PPM/S_sub selector , and improved internal layout  and more robust build in BEC to solve any problems with some camera/Tx combos. Only place to get the freshest & NEWEST Genuine OMNIBUS total Flight Controller line that each  portion of the sales goes to back to the BF project. The only place with correct updated documentation included  with the board, reinforced USB plug and Pin headers in the bag if needed, always tested and flashed the the newest firmware ! BEWARE of other shops claiming V3 when it is not, ,make sure your is a true V3 here. Others shops are buying clones  and selling as originals and do not understand.

    BEWARE OF THE CLONE-because of the popularly the direct copys have come. They are all cloning the Older V2 with a massive Current Club24A problem. We also give a portion of sales back to the community to keep improving the software.

         Now with SD card reader and Baro The Omnibus F4 Pro has the F4 processor has a Built-in Current / Voltage Sensor . Built-in OSD, video filtering, Baro, and LDO. Supports D-Shot out of the box with no Modification. Tuning could not be easier with the help of the black box SD card reader and tuning via transmitter in the OSD. It is now possible to connect your Smartaudio capable VTX . The Flip32 Omnibus flight controller uses the MPU6000 over SPI for the best possible flight performance. Along with the MPU6000 are a and an AB7456 OSD chip (an upgraded MAX7456) for the BetaFlight integrated OSD. You won't need a PDB with this build because there is a high performance 5v, 1.5a STMicrocontroller L78 voltage regulator, so you can plug the flight battery right into the flight controller.The  Flip32 Omnibus flight controller the first  F4 flight controller with a MAX7456 OSD chip directly connected to the flight controller, so it can be configured from the BetaFlight configurator.  The Omnibus F4 features the STM32F405 F4 processor, built-in BetaFlight OSD, video filtering, microsd blackbox, and BMP280 Barometer. MPU6000 Low noise Gyro, in most cases soft mounted is not necessary, and is more accurate when attached to the frame. If you do see any symptoms, we high recommend to soft mount the motors first. 

    The SmartAudio support has been included in BF3.1.0! (SmartAudio V2 VTX Control)-it is now possible to connect your Smartaudio capable VTX.  OMNIBUS F4 SD (aka OMNIBUS F4 V2) 2016-12-08 - Connect RSSI wire to RSSI input on J4. [BF] Working IR Transponder. This feature was included in the BF3.1.0 . [BF] Fully configurable software serial"

    INSTALL THE BETAFLIGHT CONFIGURATOR

    NEW OSD tab in Betaflight configurator lets you setup and configure OSD settings on the fly!

    Flip32 Omnibus was designed a 36mmx36mm (30.5mm mount holes) community version of his AIO boards. It’s called Flip32 OMNIBUS and it’s outstanding. The great thing is that the board is based on what the community really wanted and it allows a very clean build by providing pin holes for almost every connection. You can power it directly from your battery by using BAT/GND pins. The following list some of the components included:

    • STM32 F403 MCU (Spi connected to Gyro)
    • Buildin Current/Voltage sensor!
    • Firmware hex = OMNIBUSF4SD hex from dropdown. 
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • Smartaudio capable VTX PID Programming 
    • D- Shot Supported (no Modification) 
    • OSD (configured over Betaflight UI)
    • SD CARD READER + And BARO ADDED in V2
    • SBUS/PPM + DSMX Ports
    • SmartAudio V2 via J10
    • current + voltage + rssi + buzzer as pins
    • 4x 3 pin holes for ESCs + 4x signal pin holes
    • IR pins for lap timing transponder

    All Flight controllers are flashed and tested with Betaflight 3.2.1. Make sure to add the Silicone Modified Conformal Coating addition apply after testing and soldering. Protects electronics from moisture, corrosion, thermal shock, and static discharges.

    Learn More
  2. Regular Price:

    $31.99
    View Details

     ,Now Shipping v2. Pick up the Real Deal. This Flight controller is very proven and now has been tried to be copied by others, but do have access to the custom OSD chip, nor 5v regular parts, and other custom parts . To make sure everyone can get the real deal that will not fail in the air. This flight controller is at cost, and we do give betaflight $5 a board to make sure the firmware keeps growing and growing  Video In and out on pin headers and Sh connector for a no solder connection. Golden reinforced stronger USB Plug, Golden Plated though holes, Betaflight 3.0.1 loaded.

    The Flip32 Omnibus flight controller uses the MPU6000 over SPI for the best possible flight performance. Along with the MPU6000 are a barometer and an AB7456 OSD chip (an upgraded MAX7456) for the BetaFlight integrated OSD. You won't need a PDB with this build because there is a high performance 5v, 1.5a STMicrocontroller L78 voltage regulator, so you can plug the flight battery right into the flight controller.The  Flip32 Omnibus flight controller the frist  F3 flight controller with a MAX7456 OSD chip directly connected to the flight controller, so it can be configured from the BetaFlight configurator.  

    This flight controller requires BetaFlight 3.0 & Betaflight configurator to take full advantage of the OSD

    INSTALL THE BETAFLIGHT CONFIGURATOR

    NEW OSD tab in Betaflight configurator lets you setup and configure OSD settings on the fly!

    Flip32 OmniBus Micro was designed a 36mmx36mm (30.5mm mount holes) community version of his AIO boards. It’s called Flip32 OMNIBUS and it’s outstanding. The great thing is that the board is based on what the community really wanted and it allows a very clean build by providing pin holes for almost every connection. You can power it directly from your battery by using BAT/GND pins. The following list some of the components included:

    STM32 F303 MCU (Spi connected to Gyro)
    MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    OSD (configured over Betaflight UI)
    MicroSD card slot
    SBUS/PPM + DSMX Ports
    current + voltage + rssi + buzzer as pins
    4x 3 pin holes for ESCs + 4x signal pin holes
    IR pins for lap timing transponder
    Barometer

    OSD Configation has been incl. in Betaflight GUI.

    Supports SD Card and LIPO direct input (1-2S) supports 3-4 s by BEC

    MPU6000 at SPI bus.

    30x30 mm, Mounting holes 25x25mm

    Features:

    STM32 F303 MCU, Runs Betaflight 3.0 firmware

    SBUS/PPM input (Pinheaders)

    4PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)

    SPI Sensor MPU6000

    SD Card solt

    Build in Current sensor

    Barometer BMP280


    The Flip 32 OmnibusF3 flight controller is an integrated flight controller and OSD specifically designed for ease of use and outstanding flight performance. The MPU6000 inertial motion sensor was chosen for it's high reliability, accuracy and update speed. This board has no problem running fast loop times and ESC protocols. There is an onboard barometer for altitude sensing along with an On Screen Display (OSD) chip directly connected to the main processor (MCU). This tight integration between the MCU and the OSD enables fast updates to the display and easy configuration of the OSD, which is managed straight from the BetaFlight configuration tool. You no longer need to worry about the extra hassle of configuring your OSD with a USB/UART adapter and 3rd party configuration tool, it's all built into the flight control software.

    The Flip 32 OmnibusF3 was designed to work specifically with BorisB's amazing BetaFlight firmware. Boris is a control system expert and has implemented his own "ISA-PID compensator" based PID controller, called the BetaFlight PIDc, that gives an almost-predictive control for that super locked-in stick feeling. Download the BetaFlight configurator to flash and configure your quadcopter here: https://chrome.google.com/webstore/detail/betaflight-configurator/kdaghagfopacdngbohiknlhcocjccjao

    Finally, for maximum ease of use, the Flip 32  OmnibusF3 has an onboard voltage regulator that can easily handle up to a 5s battery. No need to mess with a PDB, just plug your battery straight into the flight controller and you're ready to go! Along with the robustly engineered power management system on the OmnibusF3, special precautions have been taken to ensure that the sensitive OSD chip is well protected, so you don't have to worry about any problems with your OSD. even on 5s!

    To power the board you have two options. Either connect battery directly to BAT/GND or supply 5V on one of the ESCs connections. However you obviously want to have voltage display in your OSD so just connect BAT/GND to your LiPo (up to 4S).

    To power your VTX and camera you have even more options. Out of the box RAM is not connected to anything. That leaves you with following alternatives.

    Short RAM and VBAT to get LiPo voltage. This would be unfiltered and could cause video noise.
    Short RAM and 5V to get filtered 5V from the board. This would provide clean video but 5V is probably not enought for most VTX on the market.
    Provide clean voltage from external BEC . It will provide filtered 10V for HS1177 and a VTX.

    Updated:SBUS/PPM Pin - Pin define changed since Betaflight v3.0 RC5, we use SBUS pin to read PPM input too. This can be changed Via the GUI. These are setup for SBus or PPM pin out of the box.

    Learn More
  3. Regular Price: $24.99

    Special Price $19.99

  4. Regular Price: $39.99

    Special Price $35.00

    View Details
    TUNE YOUR PIDs VIA OSD!

    Per-load with BETAFLIGHT 3.0.1  and  scarab osd 1.6.4.0! Do not bang your head on the desk trying to figure out all the firmware configuration settings. We have spent  a lot of time, so this FC & OSD is the most Ready to Fly It can be, ONLY FROM RTFQuads, we have built and know these Flight Controllers  more then anyone else, just load up the GUI and move the OSD objects around to your liking ! Less time on the bench more time in the Air! 

    get the OSD GUI HERE: https://github.com/ShikOfTheRa/scarab-osd/archive/v1.6.4.0.zip

    Make a super Clean build with less parts counts and super clean look with the 4in1 ESC. Upgraded AIO FC, based on F302 MCU, incl. F3 FC / OSD/ USB / Blackbox / Current Sensor / BEC / Compass / Baro in 35x35mm Board. Compare to F1 MCU, it supports more UART, runs faster and has Blackbox. The Connection between FC-OSD-USB will be managed automaticlly, NO DIP SWITCH needed

    • STM32 F303 MCU, Runs Cleanflight firmware 
    • no Barometer &Compasss 
    • MPU6050 
    • 8PWM output as PLUG,4x PWM output as Solder pads
    • 35x35mm, mount holes 30x30mm 
    • 128Mb Flash(16M Byte) 
    • 5v 2A BEC (up to 4s) 
    • Current and voltage sensor incl. 
    • Smart button instead of DIP switch

    Smart connection When powered by LIPO(no USB cable attached) When USB cable plug in, the USB will connect to FC automaticlly, you can change the connect to "USBOSD" by press Smart Button for 1S then release when USB cable pluged in.(Then LED shows OFF) Smart Button 's LED is ON Smart Button 's LED is ON Smart Button 's LED is OFF FC USB USB OSD FC OSD press Smart Button for 1S then release press Smart Button for 1S th

    Learn More
  5. Regular Price:

    $30.99
    View Details

    The OMNIBUS F4 , Rev 2 now has the option to have the regulator off the board if one plans to power with 5 volts. Also rev 2 has other internal RaM power improvements . Or the LDO can be installed on the board. with LDO to be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming the newest or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F4 V2.5 header through-hole is connected to UART1,DSMX receiver is UART1 port

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes

    This Flight controller is a  powerful F4 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)

    Learn More
  6. Regular Price:

    $17.99
    View Details
  7. Regular Price:

    $30.00
    View Details

    The OMNIBUS F3 PRO V3, beware of faulty v2 clones , Build in "PBD" Style current sensor and will be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F3  header through-hole is connected to UART3,DSMX receiver is UART port
    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support (Dshot600 to 1200)
    • SBUS/PPM + DSMX Ports
    • 5v3a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes
    • Low price

    This Flight controller is a  powerful F3 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. All pack with a low price, with a current sensor.


    A. OMNIBUS F3 Pro -  - Single Wire Software Serial

    PinLabelS.AudioTrampS.PortNote
    A8LED stripNGNGNG
    B4PPM (*1)OK?OKWhen PPM not in use
    B6PWM8/SCLOKOKOKI2C must be de-configured? Need furthe testing.
    B7PWM7/SDAOK??Ditto

    B. B07 (PWM7/SDA) works with S.Audio on 3.2, no extra config needed (I2C resources aren't mapped per default).

    C. Camera Control OSD with work on ANY PWM5-PWM6 using the Camera Control add on board here

    D. Extra Timer: If you are using S.BUS or other Serial RX receivers, then you can move your receiver input from SBUS/PPM header (J8) to UART3 RX (F3: J22/PWM6, F3 Pro: J12/PWM6), and make the SBUS/PPM header dedicated for PPM signal. The PPM signal is connected to MCU pin PB4, and you can use this for single-wire software serial. (see picture) This also means that when PPM is in use, UART3 cannot be used. However, if you are out of serial ports, using PPM and need one more, you can remove the SBUS resistor as described below and uncomment this line from the BetaFlight source code #define AVOID_UART3_FOR_PWM_PPM. This will enable both PPM and UART3


    1. Remove the SBUS jumper, leave PPM jumper intact.
    2. Connect SBUS signal to PWM6.
    3. Connect SmartPort signal to SBUS/PPM.
    4. Enter the CLI commands below (they will setup SBUS on UART3 also).

    Code:
    resource SERIAL_TX 11 B04
    feature -RX_PPM
    feature RX_SERIAL
    feature SOFTSERIAL
    feature TELEMETRY
    serial 2 64 115200 57600 0 115200
    serial 30 32 115200 57600 0 115200
    set serialrx_provider = SBUS

    E.


    Learn More
  8. Regular Price:

    $17.00 As low as: $15.00
    View Details

    *All unites now flashed with BetaFlight 3.1.7 and have support for D-shot ready to select from the Dropdown! D-shot Ready! 

    NOW SHIPPING V2!  S-Bus and PPM on individual pins to make use of more Uarts , Improved BEC circuity,added copper, easier Inav support, and more.... 

    Tons of features in one board with a wounder full layout. Flip F4 ; Flip32 F4 With the low noise Gyro, optimal gyro placement recommended , and not an overly super inventive gyro that will require chasing down the PID tune, Hard mounting in most cases will not hurt performance. A small portions of sales go back to the beta flight program to keep on pushing more features forward. 

    • -Uses the cc3d revolution Target vanilla default.  -updated instantaneously with new releases.
    • Stable SPI MPU-6000 Gyro 
    • D- Shot support and Flashed with D-ready firmware 
    • All through hole pin header Design  -no Sh connectors 
    • direct Lipo input :1.5A  Built-in onboard regulator - NO BEC needed. connect direct to a Lipo to power the board and Rx.
    • RaceFlight or Betaflight support on an STM32 F3 with a SPI based MPU6000 gyro - low noise gyro will not force one to soft-mount the fc
    • Boot - DFU button . ready to be Pressed 
    • Blackbox support - Max 16mb for data logging
    • SBUS/PPM input (Pinheaders) . 6PWM output (Pinheaders)
    • Spektrum satellite port for direct connection -  setup radio via USB power, woot woot!
    • STM32 F405 MCU
    • LED strip Port
    • Buzzer Port  (v2 buzzer port. working great in BF)
    • Flashed tested and Ready to Fly after setup
    • Only 36x36mm, mount holes 30.5x30.5mm
    • UART1 has three input: 1. DSM2 socket, it is no inverter,  2.pinheaders called UART TX RX, it is no inverter 3. Pinheaders called SBUS, it has inverter

    Works Perfect with RACEFLIGHT - PRE LOADED WITH RACEFIGHT. 

    Download firmware here :  http://raceflight.net/beta/REVO_BB330_FULL.bin

    Newest Latest RaceFlight Configurator ( do not use one from chome web store, it is out of date  : http://raceflight.net/rfc/cfgrf.crx

    *here Boards are shipped BetaFlight with buzzer fixed, Buzzer is working out of the box from default port*

     *RaceFlight please connect Buzzer to labeled "RSSI" port. These port are swapped in the firmware, but are working . Buzzer should be connected to Rssi Port, no code changed need, the printing on the board from the RF and BF are not the same. 

    RaceFlight has the standard modes, Arm, Angle, Horizon, Beeper, and Failsafe.  There are other modes though that really help drive performance. Some modes have sweet names like Skitzo and BrainDrain (yes these modes are named after the pilots). There are also modes that are named for what they are. Below is a full list of modes minus the standards modes already mentioned.

    Pro Smooth modes, BrainDrain, Skitzo, Landing, Delete Flash, LED On, LED Change Program, LED Change Color, BlackBox

    some of the modes are self explanatory, like Delete Flash, BlackBox, Landing, etc. We’re going to focus on the 3 modes that help drive performance; Pro Smooth mode, BrainDrain mode, and Skitzo mode.

    Skitzo Mode – Skitzo mode is unique. It essentially increases the resolution of your stick inputs into the flight controller. With Skitzo mode enabled, this resolution increase is supposed to be unlimited. This translates to smoother flight in air and allows you to make finer in flight adjustments. Leave it on all the time, it feels amazing!

    BrainDrain Mode – BrainDrain mode gives you a sharper stick feel. This isn’t the same as resolutions though. This translates more towards your rates responsiveness. It’s really good for racing when you need that super sharp stick feel on the sharp 180s for example. Having this enabled is great, but it may require some additional tuning. This is because with the sharpness increase, prop-wash can be more noticeable.

    Pro Smooth Mode – Pro smooth mode smooths your transitions. It’s most useful when you’re trying to get that absolutely stunning video of your freestyle flight. When you make stick transitions, pro smooth literally smooths them out so they’re not as jerky. You can really notice it when watching the HD video as it just makes things look smooth. You can use this in case you’re not as smooth on the sticks as Skitzo.

    RaceFlight also has some cool built in witchcraftfeatures that you can take advantage of and tweak! One such feature is called “witchcraft.” Witchcraft smooths Kd over time. Kd is Derivative in your PID controller. This helps take care of bad data and smooths the data over the course of tiny milliseconds. It comes set to a default of 16 right now, but 32 is a good number to get you started It’s something you can play and tweak to your liking.

     Raceflight is a latest flight controller firmware. By taking advantage of the processing power of F4 flight controllers, it’s able to run at 8kHz and brings the looptime down to 125 (uS). MultiShot ESC protocol which is 10 times faster than Oneshot125, 80 times faster than standard PWM signal

    Works Perfect with RACEFLIGHT - PRE LOADED WITH RACEFIGHT Or BetaFlight 3.0!

    Uses the same target and feature of the CC3D OpenPilot revolution but with more feature.

    ~ The OpenPilot Revolution board, also called 'Revo', is a new breed of Autopilot using the STM32F4 series, 210MIPS ARM Micro-controller. It contains a hardware floating point unit (FPU)which is a huge advancement for hobby-class autopilots. OpenPilot has been 32bit since day one, and the FPU is another step up the performance ladder. The FPU allows precise, low-latency processing of real-life measurements using advanced attitude estimation algorithms.

    The Revolution is a flight control computer with autopilot, intended for multirotors, helicopters and fixed wings. It is a 6DOF with gyroscope/accelerometer only,  no magnetometer and  no pressure sensors and no radio link.

    -Flexi-IO Port: JST-SH 10-pin. The receiver port can act as an input or output port depending on the configuration which is set in the Hardware Settings. Configuring the receiver port as an output port allows the user to assign more output channels then the 6 standard servo outputs.
    -MainPort: JST-SH 4-pin. This is a serial USART whose baud rate can be adjusted through the GCS. Optionally, Futaba S.Bus receiver, Spektrum/JR satellite receiver or GPS can be mapped to the MainPort. Default configuration is Telemetry for connecting an RF modem.
    -FlexiPort: JST-SH 4-pin. The function of this port also depends on the configuration and can be configured for I2C or Serial. The default configuration doesn't use this port, but it can be used for Telemetry, GPS, Spektrum satellite receivers (all working), and other I2C peripherals (under development).
    -RF Socket: Antenna connection socket for on-board OPLink modem.
    -Pwr Sen/Sonar Port: JST-SH 4-pin. This port can be configured to accommodate an Autopilot current sensor and a low cost Sonar sensor such as the HC-SR04. It can also be used as a general purpose input/output port or as a one or two channel analog input port.

    Learn More
  9. Regular Price:

    $20.99
    View Details

    The OMNIBUS F3 V3. Special RTF only v3 with through hold unpoppable  USB + other improvements , Now lower price WITHOUT  Baro.,with OSD & LDO to be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F3  header through-hole is connected to UART3,DSMX receiver is UART port

    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • SBUS/PPM + DSMX Ports
    • 5v3a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes
    • Low price

    This Flight controller is a  powerful F3 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. All pack with a low price


    A. OMNIBUS F3 -  - Single Wire Software Serial

    PinLabelS.AudioTrampS.PortNote
    A8LED stripNGNGNG
    B4PPM (*1)OK?OKWhen PPM not in use
    B6PWM8/SCLOKOKOKI2C must be de-configured? Need furthe testing.
    B7PWM7/SDAOK??Ditto

    B. B07 (PWM7/SDA) works with S.Audio on 3.2, no extra config needed (I2C resources aren't mapped per default).

    C. Camera Control OSD with work on ANY PWM5-PWM6 using the Camera Control add on board here

    D. Extra Timer: If you are using S.BUS or other Serial RX receivers, then you can move your receiver input from SBUS/PPM header (J8) to UART3 RX (F3: J22/PWM6, F3 Pro: J12/PWM6), and make the SBUS/PPM header dedicated for PPM signal. The PPM signal is connected to MCU pin PB4, and you can use this for single-wire software serial. (see picture) This also means that when PPM is in use, UART3 cannot be used. However, if you are out of serial ports, using PPM and need one more, you can remove the SBUS resistor as described below and uncomment this line from the BetaFlight source code #define AVOID_UART3_FOR_PWM_PPM. This will enable both PPM and UART3


    1. Remove the SBUS jumper, leave PPM jumper intact.
    2. Connect SBUS signal to PWM6.
    3. Connect SmartPort signal to SBUS/PPM.
    4. Enter the CLI commands below (they will setup SBUS on UART3 also).

    Code:
    resource SERIAL_TX 11 B04
    feature -RX_PPM
    feature RX_SERIAL
    feature SOFTSERIAL
    feature TELEMETRY
    serial 2 64 115200 57600 0 115200
    serial 30 32 115200 57600 0 115200
    set serialrx_provider = SBUS

    E.



    Learn More
  10. Regular Price: $45.00

    Special Price $39.99

    View Details
    Tune your PIDS via the OSD!

    r Per-load with BETAFLIGHT 3.0.1  and  scarab osd 1.6.4.0! Do not bang your head on the desk trying to figure out all the firmware configuration settings. We have spent  a lot of time, so this FC & OSD is the most Ready to Fly It can be, ONLY FROM RTFQuads, we have built and know these Flight Controllers  more then anyone else, just load up the GUI and move the OSD objects around to your liking ! Less time on the bench more time in the Air!  With BetaFlight and scarab OSD, This is the most powerful most configurable Flight controller + OSD +PDB on the market !

    get the OSD GUI HERE: https://github.com/ShikOfTheRa/scarab-osd/archive/v1.6.4.0.zip

    Make a super Clean build with less parts counts and super clean look with the 4in1 ESC. Upgraded AIO FC, based on F302 MCU, incl. F3 FC / OSD/ USB / Blackbox / Current Sensor / BEC / Compass / Baro in 35x35mm Board. Compare to F1 MCU, it supports more UART, runs faster and has Blackbox. The Connection between FC-OSD-USB will be managed automaticlly, NO DIP SWITCH needed

    • STM32 F303 MCU, Runs Cleanflight firmware 
    • Barometer BMP280 
    • Compasss HMC5983L 
    • Low noise , Super stable MPU6050 
    • 8PWM output as PLUG,4x PWM output as Solder pads
    • 35x35mm, mount holes 30x30mm 
    • 128Mb Flash(16M Byte) 
    • 5v 2A BEC (up to 4s) 
    • Current and voltage sensor incl. 
    • Smart button instead of DIP switch

    Smart connection When powered by LIPO(no USB cable attached) When USB cable plug in, the USB will connect to FC automaticlly, you can change the connect to "USBOSD" by press Smart Button for 1S then release when USB cable pluged in.(Then LED shows OFF) Smart Button 's LED is ON Smart Button 's LED is ON Smart Button 's LED is OFF FC USB USB OSD FC OSD press Smart Button for 1S then release press Smart Button for 1S th

    Learn More

Grid List

Set Descending Direction

21-30 of 51