All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.3.1! Most orders shipping same day!  Departing from Florida, U.S.A.  

Omnibus

Grid List

Set Descending Direction

1-10 of 15

Page:
  1. 1
  2. 2
  1. Regular Price: $44.99

    Special Price $38.99

    View Details

    Flip32 OMNIBUS F4 Pro Corner has all the feature one would expect from the Omnibus line but add in a Build In power distribution board. All of the Pads needed are on the TOP side, no needed to flip the board over for installs. ESC32 Telemetry pads are also on the corners to support ESC telemetry!   The Omnibus F4 Pro Corner flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfect under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.

    Omnibus F4 Pro Corner supports 3-6s LIPO direct input, build in Current Sensor and Power Filter too.

    All units flashed with stable BetaFlight 2.3.0. Take advantage of all the new features out of the box, Automatic Notch filter, turtle mode, Camera control, Increased motor output resolution, OSD improvements, and much , more

    The on Board PDB is tweaked by using 12-Layer PCB design. There is only 0.2-0.5 mohm internal resistance from input to each output pads

    • STM32 F405 MCU (Spi connected to Gyro)
    • ICM20608 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Build 12- layer level PDB
    • Able tune your pids via transmitter/Video via SmartAudio
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • SmartAudio 
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-6S).
    • 30x30mm mounting holes w/ M3 holes

    Flip32 OMNIBUS F4 Pro Corner is a  powerful F4 with a Switching power supply small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in With Build in PDB. making the most compact stack possible . You can also attach A TBS Unify Pro HV or TBS Unify Pro HV Race Edition, or others to make changes to your VTX with SmartAudio through the OSD. (Band, Channel, power, PIT Mode)


    Beware of the black clone. the PCB is not the same quality, and by cause restarts or other issues, and the gyro line is very noisy. we gave them a lead by getting comparing the worst case real one from the 10 clones we order to check the quality.  They do not use the same amount of copper and the internal resistance is higher, and this matters. 

    Learn More
  2. Regular Price:

    $34.99
    View Details

    The Flip32 OMNIBUS F4 NANO LC is a good option if you do not need a Data flash Logger on board, and you power the camera via the FC. If not the cheaper Nano V2 will be the same results. If you need a Data flash the V2 is the same layout with a Memory chip. This flight controller takes away the black box, but add a small filter to the power line on the Camera connecor now in 20x20mm mounting hole size (3m holes).Target "OMNIBUS F4" to update the firmware. With F4 and Betaflight OSD. 2-4 cell battery supported. 4s is currently supported with WITH onboard BEC , just connect to the FC and it will power., but you can still have the current and Voltage readings on the OSD, and is supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Target "OMNIBUS F4" to update the firmware
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S). 4s supported
    • 20x20mm  w/ M3 holes

    This Flip32 Omnibus F4 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board is a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, Smart Audio Support, Camera Control, ESC32 telemetry, and more. Powerful F4 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, 3.3 Volt power for spectrum users. The special feature of this Fc is a super Clean Power L/C filter to power the camera. This cuts out any extra noise in the picture for super clear video feed.

    (SBUS + SmartPort + SmartAudio + CamControl) Config:

    Code:
    # Betaflight / OMNIBUSF4SD (OBSD) 3.2.2 Nov 11 2017 / 00:39:14 (77782e602) MSP API: 1.36
    
    resource SERIAL_TX 11 A10
    
    feature SOFTSERIAL
    feature TELEMETRY
    feature LED_STRIP
    
    serial 0 32 115200 57600 0 115200
    serial 5 64 115200 57600 0 115200
    serial 30 2048 115200 57600 0 115200
    
    set serialrx_provider = SBUS

    ESC32 telemetry mod CONFIG: 

    Here is a config for the mod. Don't forget to select one of DSHOT for ESC/Motor protocol.

    Code:
    resource ADC_CURR 1 NONE
    feature ESC_SENSOR
    serial 2 1024 115200 57600 0 115200
    set current_meter = ESC
    set battery_meter = ESC


    Camera Control MOD: working with our Add on board here; try 
    inverted = off and on

    resource CAMERA_CONTROL C06
    set camera_control_ref_voltage = 295
    set camera_control_internal_resistance = 400
    set camera_control_inverted = off


    Learn More
  3. Regular Price:

    $54.99
    View Details
  4. Regular Price: $34.99

    Special Price $27.99

    View Details

    The Flip32 OMNIBUS F4 NANO now in 20x20mm mounting hole size (3m holes). Blackbox chip installed. The only place with a Data flash chip option installed on the board, and a free cable.  With F4 and Betaflight OSD. 2-4 cell battery supported. 4s is currently supported with onboard BEC , just connect to the FC and it will power., but you can still have the current and Voltage readings on the OSD, and is supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.

    • STM32 F405 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Target "OMNIBUS F4" to update the firmware
    • SBUS/PPM + DSMX Ports
    • Blackbox data flash chip
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S). 4s supported
    • 20x20mm  w/ M3 holes

    This Flip32 Omnibus F4 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board is a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, Smart Audio Support, Camera Control, ESC32 telemetry, and more. Powerful F4 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, 3.3 Volt power for spectrum users. The special feature of this Fc is it has a Black Box logging chip on board. This will allow you to log some flying and check them out on the black box viewer to see your motor graph and adjust your filters for a super crisp tune, or trouble shoot a problem.

    (SBUS + SmartPort + SmartAudio + CamControl) Config:

    Code:
    # Betaflight / OMNIBUSF4SD (OBSD) 3.2.2 Nov 11 2017 / 00:39:14 (77782e602) MSP API: 1.36
    
    resource SERIAL_TX 11 A10
    
    feature SOFTSERIAL
    feature TELEMETRY
    feature LED_STRIP
    
    serial 0 32 115200 57600 0 115200
    serial 5 64 115200 57600 0 115200
    serial 30 2048 115200 57600 0 115200
    
    set serialrx_provider = SBUS

    ESC32 telemetry mod CONFIG: 

    Here is a config for the mod. Don't forget to select one of DSHOT for ESC/Motor protocol.

    Code:
    resource ADC_CURR 1 NONE
    feature ESC_SENSOR
    serial 2 1024 115200 57600 0 115200
    set current_meter = ESC
    set battery_meter = ESC


    Camera Control MOD: working with our Add on board here; try 
    inverted = off and on

    resource CAMERA_CONTROL C06
    set camera_control_ref_voltage = 295
    set camera_control_internal_resistance = 400
    set camera_control_inverted = off
    Learn More
  5. Regular Price:

    $44.99
    View Details

    All Flight Controllers are  flashed and tested with the newest stable BetaFlight 3.2.1. Take advantage of all the new features, Automatic Notch filter, turtle mode, Camera control,DShot1200, Increased motor output resolution, OSD improvements, and much , more.

    The Flip32 OMNIBUS F7 V2 now with inertial damping gyro jacket. The case mass absorbs & resists by inertial damping the vibrations coming from the motors,props,frame, ect... -  The main function of IMU damping is so the gyro the cleanest data possible to have peak performance . also the added crash protection. The case is mounted by Gell tape and not hard mounted to the airframe in the same way a normal gyro is isolated. In our testing  this does work better then soft mounting the whole Flight Controller  

    • STM32 F745 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • IMC268 (the 6 axis SPI Gyrometer + Accelerometer)
    • D-shot Support
    • Baro

    -  All new F7 CPU to join the OMNIBUS family - Omnibus F7 Flight Controller - Dual Gyro- Baro - BF OSD -microSD - Blackbox The OMNIBUS F7  - more info to come   IN STOCK IN USA NOW SHIPPING -The Flip32 OMNIBUS F7  -  All new F7 CPU to join the OMNIBUS family  

    All Flight controllers care flashed and tested with Betaflight 3.2.1. Make sure to add the Silicone Modified Conformal Coating addition apply after testing and soldering. Protects electronics from moisture, corrosion, thermal shock, and static discharges.

    Learn More
  6. Regular Price:

    $24.99
    View Details

    The OMNIBUS F3 BEC, now with a Low noise, Low heat 1.5A BEC instead of a LDO, this will allow powering of more power demanding components off the boards BEC with no extra heat added to the board . Special RTF only v3 with through hold unpoppable  USB + other improvements , Now lower price WITHOUT  Baro.,with OSD & LDO to be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F3  header through-hole is connected to UART3,DSMX receiver is UART port

    • STM32 F303 MCU (Spi connected to Gyro)
    • Low Noise . No heat BEC 1.5A BEC
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • SBUS/PPM + DSMX Ports
    • 5v3a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes
    • Low price

    This Flight controller is a  powerful F3 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. All pack with a low price


    Learn More
  7. Regular Price: $85.99

    Special Price $79.99

    View Details

    now shipping always the newest Asgard V5.1, has all the improvements . All V5.1 are Silicone conformal coating for the protection from the elements.   Better Current Protection. 5v Regulator Upgrade. Custom Hex pre installed. Silicone conformal coating Note for 2.3 users. XM+ on UART6. Use the OMNIBUSF4SD hex. Then  ASGARD users must explicitly change the pin mapping by executing the following CLI command. "resource inverter 6 c9" - then make sure to safe  F4, with Betaflight OSD, 150A PCB and 30-40A esc's all on a 12 layer board with 2oz copper. Mounting holes 30.5 x 30.5mm. Incl. OSD / SD Card / F4 FC / Current sensor / BEC. All Flight controllers are Silicone conformal coating for the protection.  

    All units flashed with stable BetaFlight 2.3.0. Take advantage of all the new features out of the box, Automatic Notch filter, turtle mode, Camera control, Increased motor output resolution, OSD improvements, and much , more

    Now Shipping V5.1! Asgard (F4 FC+ Bl-heli_S ESCs+OSD+SD+Current Sensor) The Flip32 OMNIBUS F4 AIO aka Asgard has 4 24amp BLheli_s speed controllers built-in!  We also packed a BetaFlight OSD, Powerful F4, Current Sensor , 5v 1.5a BEC. Just connect your camera and TX, then motors and Rx, and be ReadyToFly. With Free repair service, Build-in power distribution board with current sensor on board. 2-4 cell battery supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. 

     Repair/replacement service is available if needed to get you back in the air asap. If you burn one ESC or the OSD or any other part, 90% of the time we can fix it with NO EXTRA FEE! . in worst case we are offering $45 no questions asked replacements for our customers. This covers electrical damage and fried esc’s if that should ever occur.  we are very experienced with these repairs, and most of the time can repair the Asgard with NO EXTRA FEE

    Only place were the board includes two S.H cables with the board to make the connections, a capacitor is includes with the board . it is HIGHLY RECOMMENCED to use a capacitor with this board at the input . It's a Flight Controller, PDB and Esc's all rolled into one nice little package! If space is at a premium or you are just looking to do a super clean build, then this is what you are looking for. The Asgard boasts an F4 processor and 24amp 4-in-1 esc that is compatible with the latest D-shot protocol to get that super smooth controller and crispy response.One of the awesome features about having an AIO FC is that you can tune your PIDs directly through your Transmitter via the built in OSD! Finally, no more massive flight control stacks! Using the latest Asgard ESC's combined into a simple board with the latest hardware you will get the cleanest of builds!


    What does Blheli-S 16.67 do? Means no more external beeper! just set the beeper and your motors will beep to find your quad instead of you needing to add more external parts. 


    FIRMWARE for MX and MX+  for software SBUS Inverter for XOR gates, this will be rolled into BF 3.2.0. this firmware is shipping with all new orders sent 

     https://www.dropbox.com/s/hj4jd3av8oko9ji/betaflight_3.1.6_Asgard_PC9_HIGH_SBUSInverter_Enabled?dl=0


    • STM32 F405 MCU (Spi connected to Gyro)
    • Better Current Protection w/  5v Regulator Upgrade
    • BetaFlight 3.2 with BlheliS 16.67 RC-Commands 
    • Silicone conformal coating 
    • Custom Hex pre installed; Wires and Capacitor included
    • 4 - 24A Bl_heli_s Speed controllers 
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Built in PBD
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm  w/ M3 holes\
    • comes with cables & capacitor needed for higher currents 
    • Target: Ominibus F4 SD

    This Flight controller with a powerful F4 AIO.  aka Asgard / Omnibus F4 AIO (24amp 4-in-1 ESC with Dshot + Flight Controller)

    FIRMWARE for MX and MX+  for software SBUSInverter, this will be rolled into BF 3.2.0 Inverted on Uart6

     https://www.dropbox.com/s/hj4jd3av8oko9ji/betaflight_3.1.6_Asgard_PC9_HIGH_SBUSInverter_Enabled?dl=0


    1x FC+ESC + 2 S.H connection cables



    To install with the Power BACK and FETS UP. type in the CLI

    resource MOTOR 1 B00

    resource MOTOR 2 A03

    resource MOTOR 3 B01

    resource MOTOR 4 A02

    save

    in the GUI - 

    Pitch = 180

    Yaw= 90


    24a esc, AIO, aio flight controller, airbot asgard, Airbot Asgard / Omnibus F4 AIO, Asgard, Dshot, dshot 600, omnibus aio, omnibus asgard aio, omnibus f4 aio, F4 aio, omnibus aio. Flip32 F4 Omnibus AIO


    If you would like to configure the board in a different orientation, you can learn more about Motor Remapping in BetaFlight here.  https://github.com/betaflight/betaflight/wiki/Remapping-Motors-with-Resource-Command-(3.1)

    Learn More
  8. Regular Price: $27.99

    Special Price $25.99

    View Details

    All units are tested and flashed with stable BetaFlight 2.3.4 . Supports 4s Battery input.  Take advantage of all the new features, Automatic Notch filter, turtle mode, Camera control,SmartAudio, Increased motor output resolution, OSD improvements, and much , more

    The Flip32 OMNIBUS F3 NANO in 20x20mm mounting hole size (3m holes). Target "OMNIBUS" to update the firmware. Build-in power distribution board PDB with current sensor on board. 2-4s cell battery , current and Voltage readings on the OSD. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured.  Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today,  always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.

    UART3 is used for DSM Sat AND SBUS

    Features:

    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • Target "OMNIBUS" to update the firmware
    • SBUS/PPM + DSMX Ports
    • 5v1.5a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Built in PBD ( 60 AMPS sensing) 
    • Barometer
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4s)
    • 20x20mm  w/ M3 holes
    • Note: This is the newest V3. the board color can be Black or Blue.

    This  Flip32 Omnibus F3 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, and smart Audio Support. Powerful F3 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, the on-board BEC will work for 2s-4s will support the Current sensors and voltage readings still supported over OSD, but will not have a BEC power on 4s.  This FC  will also be capable of replacement for PDB allowing you for super tight build connecting the ESC to the FC.

    Learn More
  9. Regular Price:

    $20.99
    View Details

    The OMNIBUS F3 V3. Special RTF only v3 with through hold unpoppable  USB + other improvements , Now lower price WITHOUT  Baro.,with OSD & LDO to be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F3  header through-hole is connected to UART3,DSMX receiver is UART port

    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support
    • SBUS/PPM + DSMX Ports
    • 5v3a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes
    • Low price

    This Flight controller is a  powerful F3 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. All pack with a low price


    A. OMNIBUS F3 -  - Single Wire Software Serial

    PinLabelS.AudioTrampS.PortNote
    A8LED stripNGNGNG
    B4PPM (*1)OK?OKWhen PPM not in use
    B6PWM8/SCLOKOKOKI2C must be de-configured? Need furthe testing.
    B7PWM7/SDAOK??Ditto

    B. B07 (PWM7/SDA) works with S.Audio on 3.2, no extra config needed (I2C resources aren't mapped per default).

    C. Camera Control OSD with work on ANY PWM5-PWM6 using the Camera Control add on board here

    D. Extra Timer: If you are using S.BUS or other Serial RX receivers, then you can move your receiver input from SBUS/PPM header (J8) to UART3 RX (F3: J22/PWM6, F3 Pro: J12/PWM6), and make the SBUS/PPM header dedicated for PPM signal. The PPM signal is connected to MCU pin PB4, and you can use this for single-wire software serial. (see picture) This also means that when PPM is in use, UART3 cannot be used. However, if you are out of serial ports, using PPM and need one more, you can remove the SBUS resistor as described below and uncomment this line from the BetaFlight source code #define AVOID_UART3_FOR_PWM_PPM. This will enable both PPM and UART3


    1. Remove the SBUS jumper, leave PPM jumper intact.
    2. Connect SBUS signal to PWM6.
    3. Connect SmartPort signal to SBUS/PPM.
    4. Enter the CLI commands below (they will setup SBUS on UART3 also).

    Code:
    resource SERIAL_TX 11 B04
    feature -RX_PPM
    feature RX_SERIAL
    feature SOFTSERIAL
    feature TELEMETRY
    serial 2 64 115200 57600 0 115200
    serial 30 32 115200 57600 0 115200
    set serialrx_provider = SBUS

    E.



    Learn More
  10. Regular Price:

    $30.00
    View Details

    The OMNIBUS F3 PRO V3, beware of faulty v2 clones , Build in "PBD" Style current sensor and will be powered with direct lipo. The Omnibus Flight controller line has proven itself to be one of the most reliable, speed, and feature packed boards out today. Setting the standard by which all other flight controllers are done.  Leading with way with features like a powerful F3 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads  will always have the freshest & newest genuine OMNIBUS total flight controller line up.  A portion of the flight controller sales goes toward BetaFlights developers  to make sure the firmware keeps growing. Orders are sent with correct updated documentation papers included with the board, special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure ours is a best available today,  always tested and flashed the the newest firmware.

    NOTE: OMNIBUS F3  header through-hole is connected to UART3,DSMX receiver is UART port
    • STM32 F303 MCU (Spi connected to Gyro)
    • MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    • "Drag and Drop" OSD (configured over Betaflight UI)
    • D-shot Support (Dshot600 to 1200)
    • SBUS/PPM + DSMX Ports
    • 5v3a Clean Sbec /w On-Board Video Filter
    • Built-in Current Sensor voltage + rssi + buzzer as pins
    • Barometer (SPI Baro)
    • OSD Configation has been incl. in Betaflight GUI.
    • LIPO direct input (2-4S).
    • 30x30mm mounting holes w/ M3 holes
    • Low price

    This Flight controller is a  powerful F3 with a Switching power supply  small 30x30  hole size with 3M sized holes can take direct 3S-4S power-in. All pack with a low price, with a current sensor.


    A. OMNIBUS F3 Pro -  - Single Wire Software Serial

    PinLabelS.AudioTrampS.PortNote
    A8LED stripNGNGNG
    B4PPM (*1)OK?OKWhen PPM not in use
    B6PWM8/SCLOKOKOKI2C must be de-configured? Need furthe testing.
    B7PWM7/SDAOK??Ditto

    B. B07 (PWM7/SDA) works with S.Audio on 3.2, no extra config needed (I2C resources aren't mapped per default).

    C. Camera Control OSD with work on ANY PWM5-PWM6 using the Camera Control add on board here

    D. Extra Timer: If you are using S.BUS or other Serial RX receivers, then you can move your receiver input from SBUS/PPM header (J8) to UART3 RX (F3: J22/PWM6, F3 Pro: J12/PWM6), and make the SBUS/PPM header dedicated for PPM signal. The PPM signal is connected to MCU pin PB4, and you can use this for single-wire software serial. (see picture) This also means that when PPM is in use, UART3 cannot be used. However, if you are out of serial ports, using PPM and need one more, you can remove the SBUS resistor as described below and uncomment this line from the BetaFlight source code #define AVOID_UART3_FOR_PWM_PPM. This will enable both PPM and UART3


    1. Remove the SBUS jumper, leave PPM jumper intact.
    2. Connect SBUS signal to PWM6.
    3. Connect SmartPort signal to SBUS/PPM.
    4. Enter the CLI commands below (they will setup SBUS on UART3 also).

    Code:
    resource SERIAL_TX 11 B04
    feature -RX_PPM
    feature RX_SERIAL
    feature SOFTSERIAL
    feature TELEMETRY
    serial 2 64 115200 57600 0 115200
    serial 30 32 115200 57600 0 115200
    set serialrx_provider = SBUS

    E.


    Learn More

Grid List

Set Descending Direction

1-10 of 15

Page:
  1. 1
  2. 2