All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.3.1! Most orders shipping same day!  Departing from Florida, U.S.A.  

Flight Controllers

Grid List

Set Descending Direction

31-40 of 104

  1. Regular Price: $29.00

    Special Price $20.00

    View Details
  2. Regular Price:

    $31.99
    View Details

     ,Now Shipping v2. Pick up the Real Deal. This Flight controller is very proven and now has been tried to be copied by others, but do have access to the custom OSD chip, nor 5v regular parts, and other custom parts . To make sure everyone can get the real deal that will not fail in the air. This flight controller is at cost, and we do give betaflight $5 a board to make sure the firmware keeps growing and growing  Video In and out on pin headers and Sh connector for a no solder connection. Golden reinforced stronger USB Plug, Golden Plated though holes, Betaflight 3.0.1 loaded.

    The Flip32 Omnibus flight controller uses the MPU6000 over SPI for the best possible flight performance. Along with the MPU6000 are a barometer and an AB7456 OSD chip (an upgraded MAX7456) for the BetaFlight integrated OSD. You won't need a PDB with this build because there is a high performance 5v, 1.5a STMicrocontroller L78 voltage regulator, so you can plug the flight battery right into the flight controller.The  Flip32 Omnibus flight controller the frist  F3 flight controller with a MAX7456 OSD chip directly connected to the flight controller, so it can be configured from the BetaFlight configurator.  

    This flight controller requires BetaFlight 3.0 & Betaflight configurator to take full advantage of the OSD

    INSTALL THE BETAFLIGHT CONFIGURATOR

    NEW OSD tab in Betaflight configurator lets you setup and configure OSD settings on the fly!

    Flip32 OmniBus Micro was designed a 36mmx36mm (30.5mm mount holes) community version of his AIO boards. It’s called Flip32 OMNIBUS and it’s outstanding. The great thing is that the board is based on what the community really wanted and it allows a very clean build by providing pin holes for almost every connection. You can power it directly from your battery by using BAT/GND pins. The following list some of the components included:

    STM32 F303 MCU (Spi connected to Gyro)
    MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    OSD (configured over Betaflight UI)
    MicroSD card slot
    SBUS/PPM + DSMX Ports
    current + voltage + rssi + buzzer as pins
    4x 3 pin holes for ESCs + 4x signal pin holes
    IR pins for lap timing transponder
    Barometer

    OSD Configation has been incl. in Betaflight GUI.

    Supports SD Card and LIPO direct input (1-2S) supports 3-4 s by BEC

    MPU6000 at SPI bus.

    30x30 mm, Mounting holes 25x25mm

    Features:

    STM32 F303 MCU, Runs Betaflight 3.0 firmware

    SBUS/PPM input (Pinheaders)

    4PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)

    SPI Sensor MPU6000

    SD Card solt

    Build in Current sensor

    Barometer BMP280


    The Flip 32 OmnibusF3 flight controller is an integrated flight controller and OSD specifically designed for ease of use and outstanding flight performance. The MPU6000 inertial motion sensor was chosen for it's high reliability, accuracy and update speed. This board has no problem running fast loop times and ESC protocols. There is an onboard barometer for altitude sensing along with an On Screen Display (OSD) chip directly connected to the main processor (MCU). This tight integration between the MCU and the OSD enables fast updates to the display and easy configuration of the OSD, which is managed straight from the BetaFlight configuration tool. You no longer need to worry about the extra hassle of configuring your OSD with a USB/UART adapter and 3rd party configuration tool, it's all built into the flight control software.

    The Flip 32 OmnibusF3 was designed to work specifically with BorisB's amazing BetaFlight firmware. Boris is a control system expert and has implemented his own "ISA-PID compensator" based PID controller, called the BetaFlight PIDc, that gives an almost-predictive control for that super locked-in stick feeling. Download the BetaFlight configurator to flash and configure your quadcopter here: https://chrome.google.com/webstore/detail/betaflight-configurator/kdaghagfopacdngbohiknlhcocjccjao

    Finally, for maximum ease of use, the Flip 32  OmnibusF3 has an onboard voltage regulator that can easily handle up to a 5s battery. No need to mess with a PDB, just plug your battery straight into the flight controller and you're ready to go! Along with the robustly engineered power management system on the OmnibusF3, special precautions have been taken to ensure that the sensitive OSD chip is well protected, so you don't have to worry about any problems with your OSD. even on 5s!

    To power the board you have two options. Either connect battery directly to BAT/GND or supply 5V on one of the ESCs connections. However you obviously want to have voltage display in your OSD so just connect BAT/GND to your LiPo (up to 4S).

    To power your VTX and camera you have even more options. Out of the box RAM is not connected to anything. That leaves you with following alternatives.

    Short RAM and VBAT to get LiPo voltage. This would be unfiltered and could cause video noise.
    Short RAM and 5V to get filtered 5V from the board. This would provide clean video but 5V is probably not enought for most VTX on the market.
    Provide clean voltage from external BEC . It will provide filtered 10V for HS1177 and a VTX.

    Updated:SBUS/PPM Pin - Pin define changed since Betaflight v3.0 RC5, we use SBUS pin to read PPM input too. This can be changed Via the GUI. These are setup for SBus or PPM pin out of the box.

    Learn More
  3. Regular Price: $24.99

    Special Price $19.99

  4. Regular Price: $23.99

    Special Price $19.99

  5. Regular Price:

    $19.99
    View Details
  6. Regular Price: $39.99

    Special Price $35.00

    View Details
    TUNE YOUR PIDs VIA OSD!

    Per-load with BETAFLIGHT 3.0.1  and  scarab osd 1.6.4.0! Do not bang your head on the desk trying to figure out all the firmware configuration settings. We have spent  a lot of time, so this FC & OSD is the most Ready to Fly It can be, ONLY FROM RTFQuads, we have built and know these Flight Controllers  more then anyone else, just load up the GUI and move the OSD objects around to your liking ! Less time on the bench more time in the Air! 

    get the OSD GUI HERE: https://github.com/ShikOfTheRa/scarab-osd/archive/v1.6.4.0.zip

    Make a super Clean build with less parts counts and super clean look with the 4in1 ESC. Upgraded AIO FC, based on F302 MCU, incl. F3 FC / OSD/ USB / Blackbox / Current Sensor / BEC / Compass / Baro in 35x35mm Board. Compare to F1 MCU, it supports more UART, runs faster and has Blackbox. The Connection between FC-OSD-USB will be managed automaticlly, NO DIP SWITCH needed

    • STM32 F303 MCU, Runs Cleanflight firmware 
    • no Barometer &Compasss 
    • MPU6050 
    • 8PWM output as PLUG,4x PWM output as Solder pads
    • 35x35mm, mount holes 30x30mm 
    • 128Mb Flash(16M Byte) 
    • 5v 2A BEC (up to 4s) 
    • Current and voltage sensor incl. 
    • Smart button instead of DIP switch

    Smart connection When powered by LIPO(no USB cable attached) When USB cable plug in, the USB will connect to FC automaticlly, you can change the connect to "USBOSD" by press Smart Button for 1S then release when USB cable pluged in.(Then LED shows OFF) Smart Button 's LED is ON Smart Button 's LED is ON Smart Button 's LED is OFF FC USB USB OSD FC OSD press Smart Button for 1S then release press Smart Button for 1S th

    Learn More
  7. Regular Price: $45.00

    Special Price $39.99

    View Details
    Tune your PIDS via the OSD!

    r Per-load with BETAFLIGHT 3.0.1  and  scarab osd 1.6.4.0! Do not bang your head on the desk trying to figure out all the firmware configuration settings. We have spent  a lot of time, so this FC & OSD is the most Ready to Fly It can be, ONLY FROM RTFQuads, we have built and know these Flight Controllers  more then anyone else, just load up the GUI and move the OSD objects around to your liking ! Less time on the bench more time in the Air!  With BetaFlight and scarab OSD, This is the most powerful most configurable Flight controller + OSD +PDB on the market !

    get the OSD GUI HERE: https://github.com/ShikOfTheRa/scarab-osd/archive/v1.6.4.0.zip

    Make a super Clean build with less parts counts and super clean look with the 4in1 ESC. Upgraded AIO FC, based on F302 MCU, incl. F3 FC / OSD/ USB / Blackbox / Current Sensor / BEC / Compass / Baro in 35x35mm Board. Compare to F1 MCU, it supports more UART, runs faster and has Blackbox. The Connection between FC-OSD-USB will be managed automaticlly, NO DIP SWITCH needed

    • STM32 F303 MCU, Runs Cleanflight firmware 
    • Barometer BMP280 
    • Compasss HMC5983L 
    • Low noise , Super stable MPU6050 
    • 8PWM output as PLUG,4x PWM output as Solder pads
    • 35x35mm, mount holes 30x30mm 
    • 128Mb Flash(16M Byte) 
    • 5v 2A BEC (up to 4s) 
    • Current and voltage sensor incl. 
    • Smart button instead of DIP switch

    Smart connection When powered by LIPO(no USB cable attached) When USB cable plug in, the USB will connect to FC automaticlly, you can change the connect to "USBOSD" by press Smart Button for 1S then release when USB cable pluged in.(Then LED shows OFF) Smart Button 's LED is ON Smart Button 's LED is ON Smart Button 's LED is OFF FC USB USB OSD FC OSD press Smart Button for 1S then release press Smart Button for 1S th

    Learn More
  8. Regular Price:

    $16.00
    View Details
  9. Regular Price:

    $23.00
    View Details
  10. Regular Price: $25.99

    Special Price $22.99

    As low as: $21.99
    View Details

Grid List

Set Descending Direction

31-40 of 104