All FC's are Tested and Shipped w/ NEWEST BetaFlight 3.5.1 (OCT 18th)! Departing from Florida, U.S.A.  

12 Amp

Grid List

Set Descending Direction

1-10 of 36

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  1. $13.99 As low as: $13.00
    View Details

    Aikon SEFM 20A ESC is the new generation of multirotor speed controller with the latest BLHeli_S software.

    now shipping v2.0 with Added fets 

    Aikon has been working closely with BLHeli group in developing the product for FPV racing community. The first offering of a new generation of BLHeli ESCs.  Designed to bring high performance through hardware PWM and the Silabs Busybee line of microprocessors.  Aikon SEFM 30A speedcontrollers. Busybee processor with hardware PWM timer. Has smoother RPM transition compared to a 'regular' BLHeli esc.These are OPTO ESC. This means that you will need your own 5 volt bec to power your flight controller. Thr benefits are more throttle resolution, smoother response, higher RPM ability and automatic detection of OneShot 125, OneShot 42 and Multishot protocols.

    Enable Racing Mode! (Dampened Light Mode) - Enable racing mode! Settings are changed/tuned for better handing during Racing!: BlHeli 14.6 Firmware! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers - ready for just about any motors - OneShot is included/Ready - for new and starting Flights we recommend not to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BL-Heli 14.6 Firmware ships out pre-programmed and tested.

    The SEFM 30A Blheli_S ESC is designed to give silky smooth feeling to the powerful arsenal of Blheli ESCs. Utilizing hardware PWM with the one of a kind EFM BusyBee 48MHz MCU power, SEFM30A coupled with Blheli_S firmware specifically written by Steffen for this ESC has truly bring the open source firmware to a whole new level.

    The first offering of a new generation of BLHeli ESCs. Designed to bring high performance through hardware PWM and the Silabs Busybee line of microprocessors. Stated benefits are more throttle resolution, smoother response, higher RPM ability and automatic detection of OneShot 125, OneShot 42 and Multishot protocols.

    Features

    Totally new MCU that comes with a three channel PMW output specifically designed for motor control applications and runs at 48mhz.
    New BLHELI_S firmware which provides all the strengths of the original BLHELI, but adds some significant improvements such as better response and smoother start up, 1000 steps of throttle input resolution, and auto-detection of the input signal protocol.
    Higher quality MOSFETs with extremely low internal resistance
    Three exceptionally fast dedicated MOSFET drivers
    Extra capacitance to help remove EMF spikes and keep the rest of your equipment safe.
    Specification

    Battery: 2-4s
    Constant Current: 20A
    Burst Current: 30A
    Size: 14 x 25mm
    Firmware: Blheli_S
    MCU: 8BB21
    Bootloader: Yes
    Weight (with wire) 9g
    Signal Wire Length: 150mm
    Battery Wire Length: 100mm

    Specifications:
    Continuous Current: 30A
    Burst Current: 40A
    Input Voltage: 2S-4S LiPO
    Weight: 5.5g with wires and heat shrink wrap
    Dimensions: 25x13mm

    Learn More
  2. Regular Price: $48.00

    Special Price $45.00

    The combination of Blizzards+Bazooksa+Littlebees Pro = A Cavalry packs in a 35x35MM size ready to blast all the power to the motors!  Easy Solder tabs. Strongest braking power. Littlebee smoothness and feel.

    Loaded with the newest 14.4 Firmware . With a New IC driver, this esc is one of the fastest and strongest. The new generation of high-quality IC and 396 Silabs chip imports to make smaller, lighter. With a triple IC drive everything including braking is more sensitive and rapid. Great support for 4S Batteries , making it perfect for racing. active-wheeling technology for a more efficient and quicker throttle response. Twisted pair copper wires to reduce interference signals generated within the transmission,MORE Thrust! HIGHER Top-end Endurance! BETTER Motor Efficiency! FASTER Responsive Time

     

    Bootloader: BlHeli
    Processor: SiLabs F396
    UBEC: N/A
    Lipo Supported : 2 to 4 cells
    Processor: SiLabs F396
    Bootloader: BlHeli (FC pass-throught)
    Firmware: LittleBee 20A Pro
    Servo Cable Flashable - One-Wire-Interface
    BlHeli: Dampend light enabled and OneShot42 compatible
    BlHeli:OneShot125 AutoDecect
    BEC: None
    Naked
    35mm x 35mm x 5mm
    Newest, Strongest, IC driver
    Tons of Power!
    New Dedicated fast switching gate driver

     

    Learn More
  3. $11.00
    View Details

     Flashed with DYS_XM20A_.." code.  BlHeli 14.4 ! Plug and Fly ready!  F396 Processor! 

    Enable Racing Mode! (Dampened Light Mode) - Enable racing mode! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers  - ready for just about any motors - OneShot is included/Ready - we recommend not  to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BL-Heli 14.4 Firmware ships out pre-programmed and tested.  

    MORE power! LESS HEAT the LITTLEBEE 20A! See test below 

    Specifications:

    Oneshot125 and Damped Light Capable
    NO BEC
    3S to 4S Capable
    Silabs Powered F396
    600Hz Signal Frequency
    20A throughput & 25A burst rating
    BLHeli Bootloader 
    BLHeli installed. Throttle Range fully calibrated.
    Uses new process ultra-low resistance MOSFET with miniaturization.. BLHeli Bootloader 
    Throttle fully calibrated.
    Weighs 5.8g
    Size (L x W x H) 24mm X 14mm X 4.5mm

    Learn More
  4. $31.00

    The combination of Blizzards+Bazooksa+Littlebees = A Cavalry packs in a 35x35MM size ready to blast all the power to the motors!  Easy Solder tabs. Strongest braking power. Littlebee smoothness and feel.

    Loaded with the newest 14.4 Firmware . With a New IC driver, this esc is one of the fastest and strongest. The new generation of high-quality IC and F330 Silabs chip imports to make smaller, lighter. With a triple IC drive everything including braking is more sensitive and rapid. Great support for 4S Batteries , making it perfect for racing. active-wheeling technology for a more efficient and quicker throttle response. Twisted pair copper wires to reduce interference signals generated within the transmission,MORE Thrust! HIGHER Top-end Endurance! BETTER Motor Efficiency! FASTER Responsive Time

     

    Bootloader: BlHeli
    Processor: SiLabs F330
    UBEC: N/A
    Lipo Supported : 2 to 4 cells
    Processor: SiLabs F330
    Bootloader: BlHeli (FC pass-throught)
    Firmware: LittleBee 20A
    Servo Cable Flashable - One-Wire-Interface
    BlHeli: Dampend light enabled and OneShot42 compatible
    BlHeli:OneShot125 AutoDecect
    BEC: None
    Naked
    35mm x 35mm x 5mm
    Newest, Strongest, IC driver
    Tons of Power!
    New Dedicated fast switching gate driver

     

    Learn More
  5. $9.75

     V2 now shipping. New super small size . Introducing out new ARM line of ESC. Enjoy a more efficient, smoother, more responsive flight  with a Powerful STM32F051 48MHz ARM 32-bit MCU for super fast clock rates. Main objective objectives achieved were to build with robust components to with-stain crashes and a rating (12A) is tested without cooling supplied. Tested with all the racing types of motors available. Now flashed with the newest V3.02 Firmware for OneShot42/MultiShot & OneShot125)  

    w/ 1.3 Bootloader
      (V3.05 Firmware-OneShot42/MultiShot)
    • -Developed for Racing Multicopters, Now with OneShot42/MultiShot Support!
    • - 2-4S 12Amp MAX
    • - STM32F051 48MHz ARM 32-bit MCU
    • - Precision speed control (about 1480 steps) (compared to others at 975)
    • - Rapid implementation of throttle  changes
    • - adaptive Auto Timing
    • - 24Khz PWM Frequenz
    • -30AMP RMS with no cooling needed
    • - Slim desing no additional bulky capacitors
    • - 50-500Hz input signal(PWM) or oneshot125 (up to 2000Hz)
    • - Active freewheeling enabled (little diode losses resulting in higher efficiency)
    • - Regenerative braking, therefore quick throttle response when decelerate
    • -Overcurrent protection (To protect from damages/fire reduces current as needed)
    • -Overtemperature protection (To protect from damages/fire) 
    Learn More
  6. $11.00
    View Details

     Flashed with DYS_XM20A_.." code.  BlHeli 14.4 ! Plug and Fly ready!  F396 Processor! 

    Enable Racing Mode! (Dampened Light Mode) - Enable racing mode! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers  - ready for just about any motors - OneShot is included/Ready - we recommend not  to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BL-Heli 14.4 Firmware ships out pre-programmed and tested.  

    MORE power! LESS HEAT the LITTLEBEE 20A! See test below 

    Specifications:

    Oneshot125 and Damped Light Capable
    NO BEC
    3S to 4S Capable
    Silabs Powered F396
    600Hz Signal Frequency
    20A throughput & 25A burst rating
    BLHeli Bootloader 
    BLHeli installed. Throttle Range fully calibrated.
    Uses new process ultra-low resistance MOSFET with miniaturization.. BLHeli Bootloader 
    Throttle fully calibrated.
    Weighs 5.8g
    Size (L x W x H) 24mm X 14mm X 4.5mm

    Learn More
  7. $10.00
    View Details

    Flashed with newest BlHeli firmware installed and tested!

    Based of the Mini 20A Blue series ESC, blacked out with a SiLabs 380 Processor. The Mini 30A features a UBEC and is the smallest 30A ESC With a BEC built in for the builds when one do not have to worry about another 5v power supply to power there flight controller.

    Dampened Light supported - OneShot125 auto detected Compatible

    Enable Racing Mode! (Dampened Light Mode) - Enable racing mode! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers  - ready for just about any motors - OneShot is included/Ready - we recommend not  to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BL-Heli 14.3 Firmware ships out pre-programmed and tested.  ReadyToFly

    Learn More
  8. $12.00
    View Details

    Be a Star with the Fastest, Strongest, most simplest mini ESC in town. Damped Light (Active Braking); OneShot125 Enabled with a Jumper. Each unit is powered up at RTF to check for working order. We want to make certain one is getting a working product when it leaves the door, get in the with no delay with DOA ESCs.

    Dampend light enabled and OneShot125 compatible
    BEC: None
    Lipo Cells: 2 to 4 cells
    Processor: Atmel
    Firmware: Anti-fire enabled
    Max continuous load: 30 amps
    Burst Current: 20A/30sec
    BEC: None
    Dimensions 12mm L x 23mm W x 3mm H

    2g Bare BEC. 

    Learn More
  9. $9.00

    Another Big player tossing their hat in ring. The smallest ESC to date. These are opto, so do not forget a RTF 1V-17V ADJUSTABLE VOLTAGE REGULATOR

    Comes with Bootloader installed, and SimonK firmware including OneShot auto-detect.  plus we pre-calibrate the throttle range so all ESC's start and reach full throttle at the exact same time. The Simonk AutoShot firmware is pre-calibrated with endpoints 1060us - 1860us. This corresponds to the default endpoints in both Baseflight and Cleanflight. 

    Continuous Current:18A
    Burst Current(10s):30A
    Battery:5-12NC/2-4 Lipo
    Max Power:880W
    Length:22mm
    Width:12mm
    Height:4.3mm
    Weight:5.3g

    Features

    Active Braking / Damped Light / Comp_PWM Supported
    AutoShot (OneShot125 / FastPWM Auto Detect)
    Customized to drive all motors without sync issues or cogging.
    To enable new features on Baseflight:
    - On Configuration tab, check "Enable OneShot" and "Enable FastPWM"
    - Scroll down and click "Save"

    To enable new features on Cleanflight:
    -On Configuration tab, check the "Enabled" box next to "ONESHOT125" Feature
    -Scroll down and click "Save"

     

    Learn More

Grid List

Set Descending Direction

1-10 of 36

Page:
  1. 1
  2. 2
  3. 3
  4. 4