The Flip32 OMNIBUS F4 NANO LC is a good option if you do not need a Data flash Logger on board, and you power the camera via the FC. If not the cheaper Nano V2 will be the same results. If you need a Data flash the V2 is the same layout with a Memory chip. This flight controller takes away the black box, but add a small filter to the power line on the Camera connecor now in 20x20mm mounting hole size (3m holes).Target "OMNIBUS F4" to update the firmware. With F4 and Betaflight OSD. 2-4 cell battery supported. 4s is currently supported with WITH onboard BEC , just connect to the FC and it will power., but you can still have the current and Voltage readings on the OSD, and is supported. The Omnibus Flight controller line has proven itself to be one of the most reliable,speed, and feature packed boards out today. Taking the features and setting the standard by which all other flight controllers are measured. Leading with way with features like a powerful F3/F4 processor, Betaflight OSD, current sensor, VBatt, 5v 1.5-3A BEC output, MicroSD Black Box, video output filter, and the ability to tune PIDs over video or transmitter, the list keep on growing. Now attempted been to be copied by others, that might not have all the knowledge / customized chips (OSD, 5v). RTFQuads will always have the freshest & newest genuine OMNIBUS total flight controller line up. A portion of the flight controller sales goes toward BetaFlights developers to make sure the firmware keeps growing, and adding more features. Orders are sent with correct updated documentation papers included with the board,only here we special reinforced Golden USB plug and Pin-headers in the bag. Beware of other shops claiming V3 or other ,make sure yours is a best available today, always tested and flashed the the newest Betaflight firmware.For racing or freestyle we know you demand the ultimate level of precision and accuracy the Flip32 Omnibus FC will deliver. STM32 controls OSD chip over SPI in DMA mode, less CPU using, faster rate.
- STM32 F405 MCU (Spi connected to Gyro)
- MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
- "Drag and Drop" OSD (configured over Betaflight UI)
- D-shot Support
- Target "OMNIBUS F4" to update the firmware
- SBUS/PPM + DSMX Ports
- 5v1.5a Clean Sbec /w On-Board Video Filter
- Built-in Current Sensor voltage + rssi + buzzer as pins
- OSD Configation has been incl. in Betaflight GUI.
- LIPO direct input (2-4S). 4s supported
- 20x20mm w/ M3 holes
This Flip32 Omnibus F4 Nano Flight controller with a packs a punch using the MPU6000 over SPI for the best possible flight performance on smaller crafts. Also on-board is a barometer and AB7456 OSD chip for the BetaFlight integrated OSD, Smart Audio Support, Camera Control, ESC32 telemetry, and more. Powerful F4 but with small 20x20 hole size with 3M sized holes can take direct 2S-4S power-in, 3.3 Volt power for spectrum users. The special feature of this Fc is a super Clean Power L/C filter to power the camera. This cuts out any extra noise in the picture for super clear video feed.
(SBUS + SmartPort + SmartAudio + CamControl) Config:
# Betaflight / OMNIBUSF4SD (OBSD) 3.2.2 Nov 11 2017 / 00:39:14 (77782e602) MSP API: 1.36
resource SERIAL_TX 11 A10
serial 0 32 115200 57600 0 115200
serial 5 64 115200 57600 0 115200
serial 30 2048 115200 57600 0 115200
set serialrx_provider = SBUS
ESC32 telemetry mod CONFIG:
Here is a config for the mod. Don't forget to select one of DSHOT for ESC/Motor protocol.
resource ADC_CURR 1 NONE
serial 2 1024 115200 57600 0 115200
set current_meter = ESC
set battery_meter = ESC
Camera Control MOD: working with our Add on board here; try inverted = off and on
resource CAMERA_CONTROL C06
set camera_control_ref_voltage = 295
set camera_control_internal_resistance = 400
set camera_control_inverted = off