We are quickly shipping orders with a 1man clean environment for your safety. (3/2/2020) Departing from Florida, U.S.A.  

Speed controllers

Grid List

Set Descending Direction

51-60 of 82

  1. $9.00
    View Details
    RTF Hug+ VH 20A ESCs brings the reliability and dependability you have come to expect from the hugsESCs series but with more power! In a light package, featuring damped light and Oneshot capability.  Many months in testing we wanted to bring something that will keep hugging you for more when you push your quad to the limits., We tested many Mosfets and picked the best ones for active braking properties . The new Hug+ HV are the ultimate ESC for miniquad racing and freestyle racing, now 4s supported.  They are made for Racing MultiCopters - specifically to run at 4S. They also feature ultra light weight construction with excellent thermal properties for a ESC - the MOSFETS are specifically selected to run with the least amount of heat production and highest efficiency. For Cleanflight ,Baseflight, Tau Labs, MultiWii, any flight code which is OneShot enabled - these ESCs are OneShot auto-detect ready. Download software here

    The RTF 20Amp ESC BL-Heli ships out pre-programmed and optimized for best performance - pre-configured - OneShot is included/ready autodected. ESCs are shipped ready to go - flashed with BLHeli 14 and damped light enabled (option). I highly recommend picking up USB programmer to change any settings. These are opto, so do not forget a RTF 1V-17V ADJUSTABLE VOLTAGE REGULATOR

    Enable Racing Mode! (Dampened Light Supported)

    Enable racing mode to change over 10 Settings for maximum performance: : PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123

    The main advantages of BL-Heli software is the use Active free wheel and active braking (PWM Damping) Dampened Light - 14.0.0.2 is OneShot ready for Flip32 - this actively slows the prop/motor down on one side of your Quad, while speeding the prop on the other - without "active-braking" the prop has to slow by inertia and drag alone - this DAMPING Light mode puts the brakes on - the Racing Quad handles better - but you must also increase "P" slowly in 0.1 increments to see the full benefits. Boot-loader enabled! This means all the settings can be changed over the servo cable with a simple pro mini+ftdi combo

    These ESC's have the SimonK Bootloader enabled so they can easily be flashed using the USB Linker/afro linker/Nano linker tools.

    • Oneshot capable (automatic detection) 
    • damped light enabled, (as option)
    •  fast high side switching
    • no big radial electrolytic capacitor
    • 20A continuous 30 A Bust 
    • NO BEC. LESS EMI, NO HEAT

    We also have units pre-soldered with all the wires soldered. PWM, Power, and motor wires solder and ready to go. 

    Learn More
  2. $9.00
    View Details

    Another big player tossing their hat in ring! The smallest ESC to date. These are opto, so do not forget a RTF 1V-17V ADJUSTABLE VOLTAGE REGULATOR

    Comes with SimonK bootloader installed, and flashed with newest BlHeli firmware installed and tested!. Plus we pre-calibrate the throttle range so all ESC's start and reach full throttle at the exact same time. The 18 Amp ESCs BL-Heli ships out pre-programmed and optimized for best performance - pre-configured - OneShot is included/ready, Great for Dampened Light settings.

    Enable Racing Mode! (Damped Light Supported)
    Settings are changed/tuned for better handing during Racing!  : PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123

    Continuous Current:18A
    Burst Current(10s):30A
    Battery:5-12NC/2-4 Lipo
    Max Power:880W
    Length:22mm
    Width:12mm
    Height:4.3mm
    Weight:5.3g

    Features

    Active Braking / Damped Light / Comp_PWM Supported
    AutoShot (OneShot125 / FastPWM Auto Detect)
    Customized to drive all motors without sync issues or cogging.
    To enable new features on Baseflight:
    - On Configuration tab, check "Enable OneShot" and "Enable FastPWM"
    - Scroll down and click "Save"

    To enable new features on Cleanflight:
    -On Configuration tab, check the "Enabled" box next to "ONESHOT125" Feature
    -Scroll down and click "Save"

     

    Learn More
  3. $8.50
    View Details
    Flashed with newest BlHeli 13.2.0.2 firmware installed and tested!
     
    12 Amp High Voltage RapidESC is settings the industry standard for the Go-To ESC for any mini Quad on 4s. OPTO - less EMI in the multicopter frame and less heat - you get a lot of electrical noise from 4 to 8 high amp uBECs in a radial pattern at the centre of your multicopter. less heat. less chanch of failure.
    These are the optimal flash-able ESC's for multirotors. They are all flashed and freshly wrapped with Clear shrink to show off all the PCB greatness.The F-12A HV ESC's have been tested to the tee, up-to 20.5amps all day long when used with a 2208-1800kv, 6x4.5 hq prop, showing an impressive  1050 grams of thrust.
    Super-fast throttle response, which makes your quad fly the most "locked in" feel possible. Best bang for your buck on the planet. Every ESC here is sold pre-calibrated on the throttle range so all ESC's start and reach full throttle at the exact same time
    Learn More
  4. $5.00

    turn your old syma Quadcopter to a more powerful unit with this and a mini sized FC 

    Learn More
  5. $9.00
    View Details

    Flashed with newest BlHeli firmware installed and tested!

    The Mini 20A features a UBEC and is the smallest 20A ESC With a BEC built in for the builds when one do not have to worry about another 5v power suppy to power there flight controller.

    Dampened Light supported - OneShot125  autodeacte Compatible

    Specifications

    • BlHeli: Dampend light supported and OneShot125 compatible
    • Max continuous load: 20 amps
    • Burst Current:  30A/30sec
    • BEC: 5v/1amp max
    • Lipo Cells: 2 to 4 cells
    • Processor: Atmel
    • Refresh Rate: 600hz 
    • Default timing: Medium ((Recommended for 2204) (Med-High Recommened for 2206))
    • Servo Cable Flashable - via Afro Stick, MT1501, Or Beast-Mode Flasher (Arduino Nano)
    • 27mm L x 14mm W x 5mm H
    • 10g with wires
    • 4g no-wires (bare)
    Learn More
  6. $9.00
    View Details

    The Mini 20A features a UBEC and is the smallest 20A ESC With a BEC built in, for the builds when one do not have to worry about another 5v power suppy to power there flight controller.

    The RTF Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect . Small in size (27x14.5x6mm)  supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" . No soldering a jummper pad required, it will auto-detect if OneShot is enabled), Comp PWM (Dambed light), compatible with all Lumenier motors up to 4 cell.

    The RTF 20 amp AutoShot ESCs have been tested and are compatible with all of your motors and many more with , 2S-4S, both 5" and 6" props without sync loss issues or cogging.

    The Simonk AutoShot firmware is pre-calibrated with endpoints 1060us - 1860us. This corresponds to the default endpoints in both Baseflight and Cleanflight. Therefore, "Calibration" procedure is not necessary. 

    Enable Racing mode:  We will turn on Comp_PWM + Motor_adacance timing. This can also be changed with the radip flash chrome app . All esc come with a bootloader. 

    Features

    Active Braking / Damped Light / Comp_PWM
    AutoShot (OneShot125 / FastPWM Auto Detect)
    Customized to drive all motors without sync issues or cogging.
    To enable new features on Baseflight:
    - On Configuration tab, check "Enable OneShot" and "Enable FastPWM"
    - Scroll down and click "Save"

    To enable new features on Cleanflight:
    -On Configuration tab, check the "Enabled" box next to "ONESHOT125" Feature
    -Scroll down and click "Save"

    Specifications

    Max continuous load: ~20 amps
    Burst Current: 30A/10sec
    BEC: 5v/1amp max
    Lipo Cells: 2 to 4 cells
    Cables are fitted with female 2mm bullet connectors
    Weight: 4g (board) 8g (total with wires and connectors)
    High quality N-FET only flashed with SimonK firmware and 5v 1A BEC
    Dimensions

    27mm L x 14.5mm W x 6mm H
    100mm signal wire / 5v power
    50mm motor wires 
    70mm ESC power wires

    Dampened Light supported - OneShot125  autodeacte Compatible

    Specifications

    • BlHeli: Dampend light supported and OneShot125 compatible
    • Max continuous load: 20 amps
    • Burst Current:  30A/30sec
    • BEC: 5v/1amp max
    • Lipo Cells: 2 to 4 cells
    • Processor: Atmel
    • Refresh Rate: 600hz 
    • Default timing: Medium ((Recommended for 2204) (Med-High Recommened for 2206))
    • Servo Cable Flashable - via Afro Stick, MT1501, Or nano Flasher (Arduino Nano)

    Dimensions

    • 27mm L x 14mm W x 5mm H
    • 10g with wires
    • 4g no wires (bare)
    Learn More
  7. $25.00
    View Details

    NOW WITH BLHeli Boot-loader! Update settings easy with 1 wire interface!

    Flashed with newest BlHeli 14.4 firmware installed and tested! RTF 12A  BL-Heli '4-in-1" ESC are made for any MultiCopter - specifically to run at 2s,3S or 4S they also feature ultra light weight  gram construction with excellent thermal properties. - the MOSFETS are specifically selected to run BL-Heli WITH active damping code with the least amount of heat production and highest efficiency. This is opposite to the majority of ESCs retrofitted with SimonK or BL-Heli which actually run much hotter and are less efficient - We have selected very carefully the BEST mosfets to run on BLHEli code - These ESC are perfect for 3S or 4S pro-spec Quads. These ESC have OneShot enabled auto-detected code installed. - Damped Light Mode and Oneshot capable.

    RTF Mini "4-in-1" 12-Amp 35x35 HIGH VOLTAGE up to 4s- Damped Light Mode and Oneshot capable.

    Users will need to install and wires. no extra cap needed

    Please note: This is for more advanced users. Good soldering is a must. Watch to make sure the solder does not overflow to the mosfets.

    Watch your spacer size, the clearance is minimal. 3mm spacers work best, but you may still need to file down the thick edges.

     

    Learn More
  8. Regular Price: $9.00

    Special Price $8.50

    View Details
    Flashed with newest BlHeli v14.4 (4.2016) firmware installed and tested! We get Factory Direct. All of the units shipped are manufactured 4/15/2016  They are ready to ship, ESC only orders will ship in less then 24 hours. The date code are 4.2016 Date code. March  Every unit tested under load, and solder visually inspected. BUY WITH CONFIDENCE, These ESC have overcome been obsessively engineered and now Strongest, Smallest, fastest, most reliable mini-ESC around!!! Zero PCB failure rate in this batch! 
    ESC Features:
    Specially for Multi-copter, throttle respond fast;
    Suit for throttle, which can compatible well with motor;
    Throttle signal is twisted pair cable, reduce the crosstalk while the signal transfer by the copper wire and flight more stable; 
    The maximum refresh frequency up to 500Hz throttle signal, compatible with all flight controls;
    Use new process ultra-low resistance MOSFET with miniaturization, and all flashes are N MOS with high withstanding current;
    Minaturization design, Mini16/20A with high performance capacitor fliter on the board, weight reduce to 2g, also already thicken the PCB copper specially and low heat for small aircraft.
    Enable Racing Mode! (Dampened Light Supported)
    Settings are changed/tuned for better handing during Racing!  : PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123
    • Specification:
    • BlHeli pre-flashed  14.3
    • Damped Light Ready; Oneshot Ready
    • Oneshot Ready (plug and play with flip32)
    • Small (kiss size) (only 2 grams without wires)
    • Up to 600Hz signal
    • ultra-low resistance all MOSFET design
    • BLHeli or simonK bootloader enabled
    • Flashable via the servo leads
    • Voltage: 6-16.8V(2-4S LiPo)
    • Output Current: 20A
    • BEC: Without
    • Signal frequency: 20-500Hz
    • Output PWM frequency:18KHz
    • Firmware:BLHELI-(ONESHOT)
    • Weight:2.0g(without wires)
    • Size:23*12*4.5mm
    Learn More
  9. Regular Price: $9.00

    Special Price $8.50

    View Details
    Flashed with newest 2016-04-15- march firmware installed and tested! We get Factory Direct. All of the units shipped are manufactured 4/6/2015  They are ready to ship, ESC only orders will ship in less then 24 hours. The date code are 4.2016 Date code . Every unit tested under load, and solder visually inspected. BUY WITH CONFIDENCE, These ESC have overcome been obsessively engineered and now Strongest, Smallest, fastest, most reliable mini-ESC around!!! Zero PCB failure rate in batch testing! 
     
     SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads.  The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature)
    ESC Features:
    Specially for Multi-copter, throttle respond fast;
    Suit for throttle, which can compatible well with motor;
    Throttle signal is twisted pair cable, reduce the crosstalk while the signal transfer by the copper wire and flight more stable; 
    The maximum refresh frequency up to 500Hz throttle signal, compatible with all flight controls;
    Use new process ultra-low resistance MOSFET with miniaturization, and all flashes are N MOS with high withstanding current;
    Minaturization design, Mini16/20A with high performance capacitor fliter on the board, weight reduce to 2g, also already thicken the PCB copper specially and low heat for small aircraft.

    Specification:

    Voltage: 6-16.8V(2-4S LiPo)
    Output Current: 20A
    BEC: Without
    Signal frequency: 20-500Hz
    Output PWM frequency:18KHz
    Firmware:SimonK firmware w./ bootloader
    Weight:2.0g(without wires)
    Size:23*12*4.5mm

    Learn More
  10. $8.00
    View Details
    Flashed with newest BlHeli 13.2.0.2 firmware installed and tested!
    (the newest 13.2.0.0 firmware is compatible running conjugation with all 13.x.x firmware)
    RTF F-15A ESCs Bring Fire with Fire when you smoke everyone without the BL-Heli active braking version - made to make you the king (or queen) of Racing MultiCopters - specifically to run at 3S-4S. For Cleanflight ,Baseflight, Tau Labs any flight code which is OneShot enabled - these ESCs are OneShot auto-detect ready.
     
    The RTF 15Amp ESC BL-Heli ships out pre-programmed and optimized for best performance - pre-configured - OneShot is included/Ready
    The F-15A ESC's have been tested to the tee, up-to 22amps all day long when used with a 2208-1800kv, 6x4.5 hq prop, showing an impressive 950 grams of thrust.
    This ESC is a little thicker then the standard F-12 Fire Red and a heat sink is needed (included) but it will give one able headroom when running 4S.
     
    Enable Racing Mode! (Dampened Light Supported)
    Settings for : PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123
     
    The main advantages of BL-Heli software is the use active free wheel and active braking (PWM Damping) Dampened Light - 13.1 is OneShot ready for Flip32 - this actively slows the prop/motor down on one side of your Quad, while speeding the prop on the other - without "active-braking" the prop has to slow by inertia and drag alone - this DAMPING Light mode puts the brakes on! - the Racing Quad handles better - but you must also increase "P" slowly in 0.1 increments to see the full benefits. Boot-loader enabled! This means all the settings can be changed over the servo cable with a simple pro mini+ftdi combo
    Learn More

Grid List

Set Descending Direction

51-60 of 82