Flight Controller Tested and Flashed shiped BetaFlight 4.0.5 (8/7/2019)! Departing from Florida, U.S.A.  

Speed controllers

Grid List

Set Ascending Direction

11-20 of 82

  1. $25.00
    View Details

    RTF Mini "4-in-1" 12-Amp 35x35 

    Users will need to install cap and wires. 

     

    Please note: This is for more advanced users. Good soldering is a must.

    Watch your spacer size, the clearance is minimal. 3mm spacers work best, but you still need to file down the thick edges.

    5-15-13 simonk firmware installed. 

    Learn More
  2. $7.50
    View Details

    RTFHugESCs were developed to hug your multicopter frame, maximizing performance, so you can kiss your racing foes goodbye . Featuring ultra light weight construction with excellent thermal properties for an ESC - the MOSFETS are specifically selected to run SimonK with the least amount of heat production and highest efficiency.  Users will need to install wires.

    These ESC's have the SimonK Bootloader enabled so they can easily be flashed using the USB Linker/afro linker/Nano linker tools.

    Features
    All Nfets (bsnfet.hex)
    12Amp constant with 15Amp burst (In good air flow)
    NO BEC OPTO!
    2 and 3S Capable (no 4S please)
    ultra light weight 1.5g PCB.  couple more grams with all motors and power wires. 
    400hz and 490hz compatible - DJi, naze32, cc & MultiWii tested with mni motors to 25,000rpm


    Learn More
  3. $8.00
    View Details

    OPTO - less EMI in the multicopter frame and less heat - you get a lot of electrical noise from 4 to 8 high amp uBECs in a radial pattern at the centre of your multicopter

    These ESCs will give your multi rotor quicker reflexes, less drift, and smoother flights. These are so fast, compared to standard ESCs you can double your PI gains! ALL ESCs are flashed with the most current version of the famous SimonK firmware. Future software updates can be performed through the servo cable eliminating the need for complicated flashing jigs.

    **Currently we are flashing them with SimonK 5-15-13 firmware to be compatible with the Sunnysky X2204 motors, etc.

    Get one normal and three without BEC is an optimal setup for racing quad 

    12 Amp RapidESC BLHeli multi can also be flashed. For most users we find SimonK plays best with almost all flight controllers, for an amazing flight. If you want to play around with BLheli, try to changing Standard config to:1. timing set to med-hi, 2. demag compensation set to off, may require more changes for your battery/motor setup. For more info on BLHeli go here 

    Learn More
  4. $9.00
    View Details

    The Opera ESC will replace and improve your stock ESCs in your DJ Phantom. Loaded with ultra-fast SimonK, that will reduce all the "shakes" and enable you to increase your gains for a more stable craft. They are a direct fit, but not a direct "replacement"- 4 are needed to get started.  The MOSFETS are specifically selected to run SimonK with the least amount of heat production and highest efficiency.  After years of testing we have selected very carefully the BEST mosfets to run on SimonK - these ESC are perfect for 3S or 4S.

    Super bright led on the bottom. You can change the color with a jumper on the esc. (see pics for further illustration)

    Features:
    • All N-channel FETs
    • External Oscillator
    • Boot-loaded Enabled
    • 2-4s Capable
    • Weight: 20grams
    • Direct fit in DJI Phantom 1 and 2 
    • LEDS on the Bottom (color is changable)
    • NO UBEC on baord for super cool opertion.
    • 400hz and 490hz compatible - DJi, naze32, cc & MultiWii tested
    • Update with BSNET.HEX 
    • uSEC range  These are programmed to SimonK - idle ≤1064   - mid 1464 -  high throttle ≥1864 uSec 
    •  MOSFETS are specifically selected to run SimonK
    • Program card - Does not require or use any program card

     

    Learn More
  5. $13.00
    View Details

    new 3.0. New and Improved LDO, layout and pads, now with HIGHER RATED CAPACITORS INSTALLED & IMPROVE PAD AND PLACMENT. NOw Flashed with the newst BLHELI 14.3!  This 18A Version uses higher rated top notch fets which are able to withstand higher currents compared to the 12A Version.Supporting the highest cell count for the Smallest ESC in its class, just 2g bare PCB. 2-6s compatible. Yes. up to six (6s) cell support. 

    RTF Bear HugESCs were developed to hug your multicopter frame, maximizing performance, so you can kiss your racing foes goodbye . Featuring ultra light weight construction with excellent thermal properties for an ESC - the MOSFETS are specifically selected to run BLHeli with the least amount of heat production and highest efficiency.  Users will need to install wires (INCLUDED). Clock and Data lines are on "easy" to solder for easy prgamming. The newest BLHeli (multirotor) Installed and Tested

    Enable Racing Mode! (Dampened Light Mode) - Enable racing mode! For True Plug and Play settings, more flying and less time on the bench. Racing mode is pre-programmed and optimized for best performance by quadcopter racers  - ready for just about any motors - OneShot is included/Ready - we recommend not  to alter our BL-Heli settings for racing quads. Race mode changes over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance! Pair with a Flip32 for automatic detection of all the advantages of Oneshot123. Newest BLHeli 14.3 Firmware ships out pre-programmed and tested.  

    -Reverse motor direction easily
    -Supports damped light mode,demag, timming, and countless other settings
    - Pads on edge for easy programming ! (see pic)
    - Advantages of further advancements in BLHeli by flashing new firmware
    -Set other parameters such as beacon, PPM range etc
    - Many setting for any  motor/battery/prop combo

    Features
    All Nfets - 14.3.0.2 Firmware 
    18Amp constant(In good air flow)
    Easy to reach programing pads
    NO BEC OPTO!
    2s and 6S Capable (yes. 4S please)
    Ultra light weight 2g PCB.  couple more grams with all motors and power wires. 
    400hz and 490hz compatible - DJi, naze32, cc & MultiWii tested with mni motors to 25,000rpm
    Size:  22mmX12mm

    3.0V  NOW SHIPPPING : HIGHER RATED CAPACITORS INSTALLED  :  IMPROVE PAD AND PLACMENT 

     

    Learn More
  6. $25.00
    View Details

    RTF Mini "4-in-1" 12-Amp 35x35 HIGH VOLTAGE up to 4s

    RTF  "4-in1" 12 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on any MultiCopters. This ESC is small in size (35mmX35mmx6mm) and big on power, supporting 22A on 4s , testing up to 250watts per channel . The ESC comes pre-loaded with the newest simonk  firmware, which is compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible withanymost all  motors up to 4 cell.

    The RTF 12 amp AutoShot 4-in1 ESC has been tested and are compatible with all RTF motors , 2S-4S, both 5" and 6" props without sync loss issues or cogging.

    Users will need to install and wires. no extra cap needed

    Please note: This is for more advanced users. Good soldering is a must.

    Watch your spacer size, the clearance is minimal. 3mm spacers work best, but you still need to file down the thick edges.

     

    Learn More
  7. $7.50
    View Details
    Flashed with newest BlHeli 14.0.0.2 firmware installed and tested!
    (the newest firmware is compatible running conjugation with all 13.x.x firmware)
    RTF Hugs 12A ESCs will have all the groupies hugging you when you whip out the BL-Heli active braking version. They are made for Racing MultiCopters - specifically to run at 3S. They also feature ultra light weight construction with excellent thermal properties for a ESC - the MOSFETS are specifically selected to run with the least amount of heat production and highest efficiency. For Cleanflight ,Baseflight, Tau Labs, MultiWii, any flight code which is OneShot enabled - these ESCs are OneShot auto-detect ready.   Download software here

    The RTF 12Amp ESC BL-Heli ships out pre-programmed and optimized for best performance - pre-configured - OneShot is included/ready

    Enable Racing Mode! (Dampened Light Supported)

    Enable racing mode to change over 10 Settings for maximum performance: : PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123

    The main advantages of BL-Heli software is the use Active free wheel and active braking (PWM Damping) Dampened Light - 13.1 is OneShot ready for Flip32 - this actively slows the prop/motor down on one side of your Quad, while speeding the prop on the other - without "active-braking" the prop has to slow by inertia and drag alone - this DAMPING Light mode puts the brakes on - the Racing Quad handles better - but you must also increase "P" slowly in 0.1 increments to see the full benefits. Boot-loader enabled! This means all the settings can be changed over the servo cable with a simple pro mini+ftdi combo

    These ESC's have the SimonK Bootloader enabled so they can easily be flashed using the USB Linker/afro linker/Nano linker tools.



    Learn More
  8. $8.00
    View Details
    Flashed with newest BlHeli 13.2.0.2 firmware installed and tested!
    (the newest firmware is compatible running conjugation with all 13.x.x firmware)
    RTF F-12A ESCs Bring Fire with Fire when you smoke everyone without the BL-Heli active braking version, made to the king for Racing MultiCopters - specifically to run at 3S-4S. They also feature ultra light weight construction with excellent thermal properties for a ESC - the MOSFETS are specifically selected to run with the least amount of heat production and highest efficiency. For Cleanflight ,Baseflight, Tau Labs, MWii, any flight code which is OneShot enabled - these ESCs are OneShot auto-detect ready.
    The RTF 12Amp ESC BL-Heli ships out pre-programmed and optimized for best performance - pre-configured - OneShot is included/Ready
     
    Enable Racing Mode! (Dampened Light Supported)
    Enable racing mode to change over 10 Settings for maximum performance : PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123
     
    The main advantages of BL-Heli software is the use Active free wheel and active braking (PWM Damping) Dampened Light - 13.1 is OneShot ready for Flip32 - this actively slows the prop/motor down on one side of your Quad, while speeding the prop on the other - without "active-braking" the prop has to slow by inertia and drag alone - this DAMPING Light mode puts the brakes on! - the Racing Quad handles better - but you must also increase "P" slowly in 0.1 increments to see the full benefits. Boot-loader enabled! This means all the settings can be changed over the servo cable with a simple pro mini+ftdi combo
    Learn More
  9. $8.00
    View Details
    Flashed with newest BlHeli 13.2.0.2 firmware installed and tested!
    (the newest firmware is compatible running conjugation with all 13.x.x firmware)
    RTF B-12A ESC Run cool as ice when your ducking trees with the BL-Heli active braking version, are made for Racing MultiCopters - specifically to run at 2-4S. They also feature ultra light weight construction with excellent thermal properties for a ESC - the MOSFETS are specifically selected to run with the least amount of heat production and highest efficiency. For Cleanflight ,Baseflight, Tau Labs, MWii, any flight code which is OneShot enabled - these ESCs are OneShot auto-detect ready.
    The RTF 12Amp ESC BL-Heli ships out pre-programmed and optimized for best performance -pre-configured- OneShot is included/Ready
     
    Enable Racing Mode! (Dampened Light Supported)
    Enable racing mode to change over 10 Settings for maximum performance: PWM Frequency/Damped, Motor Timing, Beacon strength/Delay,PPM MIN/MAX Throttle are set to maximum performance!  Pair with a Flip32 for automatic detection of all the advantages of Oneshot123
     
    The main advantages of BL-Heli software is the use Active free wheel and active braking (PWM Damping) Dampened Light - 13.1 is OneShot ready for Flip32 - this actively slows the prop/motor down on one side of your Quad, while speeding the prop on the other - without "active-braking" the prop has to slow by inertia and drag alone - this DAMPING Light mode puts the brakes on! - the Racing Quad handles better - but you must also increase "P" slowly in 0.1 increments to see the full benefits. Boot-loader enabled! This means all the settings can be changed over the servo cable with a simple pro mini+ftdi combo
    Learn More
  10. $8.00
    View Details
    Flashed with newest BlHeli 13.2.0.2 firmware installed and tested!
    (the newest firmware is compatible running conjugation with all 13.x.x firmware)
    OPTO - less EMI in the multicopter frame and less heat - you get a lot of electrical noise from 4 to 8 high amp uBECs in a radial pattern at the centre of your multicopter
    These ESCs will give your multi rotor quicker reflexes, less drift, and smoother flights. These are so fast, compared to standard ESCs you can double your PI gains! ALL ESCs are flashed with the most current version of the famous  BLHeli. Future software updates can be performed through the servo cable eliminating the need for complicated flashing jigs.

    All ReadToFlyQuads ESCs come ready to fly, preset with BLHeli settings to accomodate high kv motors used in most miniquads, including the Advanced 2204 1900/2300kv, House 2300kv, or any 1806 2300kv motor etc. For most setups there is no need for further configuration.  but with the bootloader enables  all the  programming can be done via the  USB programmer over the servo line

    One BEC and three without BEC is an optimal setup for racing quad.

     

    Learn More

Grid List

Set Ascending Direction

11-20 of 82